Jump to content


Photo

Shot counters for my Stryfe and Rapidstrike


37 replies to this topic

#26 Nemesis2

Nemesis2

    Member

  • Members
  • 4 posts

Posted 22 January 2016 - 06:54 AM

Hi kingbob

Great write up and thanks for sharing the project with the community.
Are you able to post the codes for this.
This is something which I have been thinking about but am not very good with coding.
Any help would be appreciated
  • 0

#27 meltedspades

meltedspades

    Member

  • Members
  • 6 posts

Posted 24 January 2016 - 12:02 PM

The 2 hall effect sensors i used are capable of detecting 9 different magazine sizes between them (and only using 2 inputs in the arduino). Thats more than enough for all the nerf magazines: 6, 12, 18, and 18, 25, 36 drums. But yes could add a 4 bank dip switch accessible from outside somewhere. But the magnets i used were like $3 for 50 on ebay, and only takes a few seconds to add one to a clip.

 

Btw if anyone wants the Arduino code for the circuit above, happy to share.

please do share the code (pastebin it - I assume at least 100+ lines of code)


  • 0

#28 Kingbob

Kingbob

    Member

  • Members
  • 133 posts

Posted 25 January 2016 - 07:38 AM

Source files here:

Rapidstrike: https://drive.google...iew?usp=sharing

Stryfe: https://drive.google...iew?usp=sharing

 

They're pretty much the same, but the Stryfe version is setup for a switch for the trigger counter. The Rapidstrike version is set to use a hall effect sensor and magnet for the counter. Both have the code for each, but commented out the non relevant part. You'll see when you look. They'll work in any gun, i just differentiate them by how the trigger counter is activated.

 

Its pretty well commented so you should be able to work out whats what, where to change pin assignments, timings etc. 

Its currently only setup for a 6, 12, or 18 magazine. But you can easily add 25 and 36 detection. 

 

Its also sensitive to the direction of the magnets (north or south) so test before gluing any in place.

 

You'll also need the LEDControl.h library from here: https://github.com/w...ontrol/releases

If you dont know how to install a library, info here: https://www.arduino....Guide/Libraries

 

 

Any questions, happy to answer, and any suggestions, happy to hear!


Edited by Kingbob, 25 January 2016 - 07:41 AM.

  • 0

#29 DjOnslaught

DjOnslaught

    Member

  • Members
  • 350 posts

Posted 25 January 2016 - 09:37 AM

What kinda trigger switch did you utilize for the stryfe trigger counter?
  • 0

#30 Kingbob

Kingbob

    Member

  • Members
  • 133 posts

Posted 25 January 2016 - 09:55 AM

What kinda trigger switch did you utilize for the stryfe trigger counter?

 

Just a micro lever switch, some pics on the first page.

 

9.JPG


  • 0

#31 DjOnslaught

DjOnslaught

    Member

  • Members
  • 350 posts

Posted 25 January 2016 - 01:44 PM

 
Just a micro lever switch, some pics on the first page.
 
9.JPG


Ok, just a momentary switch. Did you happen to have a wiring diagram for the entire thing? I don't think I saw one on the front page.
  • 0

#32 Kingbob

Kingbob

    Member

  • Members
  • 133 posts

Posted 25 January 2016 - 11:53 PM

Ok, just a momentary switch. Did you happen to have a wiring diagram for the entire thing? I don't think I saw one on the front page.

 

Theres a full circuit diagram in post #14:

http://nerfhaven.com...ke/#entry349981

 

Also in the first post as an update/link.


  • 0

#33 Nemesis2

Nemesis2

    Member

  • Members
  • 4 posts

Posted 26 January 2016 - 06:29 AM

Hi Kingbob

Thanks for sharing this information with the nerf community.
  • 0

#34 Kingbob

Kingbob

    Member

  • Members
  • 133 posts

Posted 26 January 2016 - 09:26 AM

Hi Kingbob

Thanks for sharing this information with the nerf community.

 

No worries.

 

Heres a peek at my next one :D

 

http://www.youtube.c...h?v=Xj6GkkIPjXw


  • 0

#35 Nathaniel Deal

Nathaniel Deal

    Member

  • Members
  • 11 posts

Posted 04 February 2016 - 11:32 AM

Hey I made a Nerf dart counter its kinda similar, check it out and let me know what you think!


Edited by Nathaniel Deal, 07 February 2016 - 03:36 PM.

  • 0

Nathaniel Deal
Youtube: Nathaniel Deal

Check out my Nerf Dart Counter!


#36 Kingbob

Kingbob

    Member

  • Members
  • 133 posts

Posted 05 February 2016 - 12:05 AM

Without wanting to sound insulting, if i still need to provide an Arduino, a power source, a counting mechanism, and trigger mechanism to make your counter work, then what does your counter actually do?


  • 0

#37 Nathaniel Deal

Nathaniel Deal

    Member

  • Members
  • 11 posts

Posted 07 February 2016 - 03:53 PM

No worries!

 

Its a base kit to build a modified blaster that includes a dart counter. I also provide circuits, arduino code and setup instructions. The Arduino is available from a lot of sources so I chose not to supply it. 

 

The following variables keep me from providing a one size fits all solution. 

  • Blaster type (Semi or Auto trigger)
  • Internal or external installation 
  • Modded battery source

And once those things are determined all the other parts can be sources by the buyer.

 

Let me know if that answers your question.


  • 0

Nathaniel Deal
Youtube: Nathaniel Deal

Check out my Nerf Dart Counter!


#38 Kingbob

Kingbob

    Member

  • Members
  • 133 posts

Posted 02 November 2016 - 02:06 AM

Occurred to me i never posted a pic of what my Rapidstrike ended up like. I ended up adding nerf sights, and made a suppressor out of some pvc pipe from a hardware store. 

Put a 9 LED flashlight on the right hand side, which just has a rear mounted pushbutton switch.

Put a laser on the left hand side, which has a momentary switch on the grip in just the right spot for the thumb. (Its the red dot behind the motor switch).

 

DSC_0150.JPG

 

DSC_0151.JPG


  • 0


1 user(s) are reading this topic

0 members, 1 guests, 0 anonymous users