Jump to content


Photo

Usable Dimensions for Rapidstrike tray


6 replies to this topic

#1 CS- Tiff

CS- Tiff

    Member

  • Members
  • 99 posts

Posted 02 January 2015 - 09:55 AM

Does anybody know how small my lipo has to be to fit in the stock battery compartment? I can always remove the back and keep the end cap to add space.
  • 0

#2 Love777

Love777

    Member

  • Members
  • 22 posts
  • State:Florida
  • Country:United States

Posted 02 January 2015 - 10:44 AM

I am not sure if larger than this will fit but a 2 cell lipo (11.1V) would fit fine with plenty of room in the battery tray. Also I would recommend that as a good balance of power vs accuracy. The 3 cell lipos tend to hurt your dart accuracy too much in my experience.
  • 0

#3 CS- Tiff

CS- Tiff

    Member

  • Members
  • 99 posts

Posted 02 January 2015 - 02:44 PM

2 cell lipos can be in any size or shape. I want to know the dimentions like, 100mm x 30mm x 20mm.

EDIT: 2s is actually 7.4v. 3s is 11.1v. Were you saying 2s or 3s?

Edited by CS- Tiff, 02 January 2015 - 02:46 PM.

  • 0

#4 Love777

Love777

    Member

  • Members
  • 22 posts
  • State:Florida
  • Country:United States

Posted 02 January 2015 - 04:37 PM

I will have to go home and look at my lipo (I don't usually use them) but yes must be a 3 cell then. To not make this thread get bumped a bunch will PM you the one I have.
  • 0

#5 MAV13

MAV13

    Member

  • Members
  • 125 posts
  • Location:Baltimore, MD
  • State:Maryland
  • Country:United States

Posted 03 January 2015 - 06:55 PM

For what it's worth, a 7.2V sub-C NiMH/NiCd pack will fit in there but only if you gut out the internal ribbing and minimize the end cap as much as possible. I would say the max length you can get if you shave everything out is a little over 5 inches and around 2.5 inches wide.
  • 0

#6 Lunas

Lunas

    Member

  • Members
  • 141 posts
  • Location:57501
  • State:South Dakota
  • Country:United States

Posted 03 January 2015 - 07:49 PM

I used my calipers a while back to measure mine it is about 28mm deep 117mm long and 54mm wide you should be able to fit 2 26650 batteries side by side if you cut out the center support and the 2 end supports you will have about 1cm at each end of the battery you would need to adjust for...

Ill redo my measurements later tonight and repost but those are the numbers i remember from when i measured mine. you do get a bit more room by dropping the tray and just using the front. But I like to keep my nerf guns semi stock and would like to if i have to drop back to stock.

Edited by Lunas, 03 January 2015 - 07:52 PM.

  • 0

#7 CS- Tiff

CS- Tiff

    Member

  • Members
  • 99 posts

Posted 03 January 2015 - 08:45 PM

I used my calipers a while back to measure mine it is about 28mm deep 117mm long and 54mm wide you should be able to fit 2 26650 batteries side by side if you cut out the center support and the 2 end supports you will have about 1cm at each end of the battery you would need to adjust for...

Ill redo my measurements later tonight and repost but those are the numbers i remember from when i measured mine. you do get a bit more room by dropping the tray and just using the front. But I like to keep my nerf guns semi stock and would like to if i have to drop back to stock.


Thank you this is exactly what I wanted to know. Now I can fit my 3s that I wanted to order in there.
  • 0


0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users