Jump to content


Photo

Where to get PETG at pet store website

Need to know where to look for Petg in petstore website like Petco.com

9 replies to this topic

#1 rockinon96

rockinon96

    Member

  • Members
  • 142 posts
  • Location:Brasher Falls
  • State:New York
  • Country:United States

Posted 09 July 2014 - 12:17 PM

I want to get 1/2 inch Petg, But I don't have a pet store near me, closest one is 2.5 hours away, and I don't have my own car. Could you guys could you put a link to it so I can buy it right away. Thank you for your time
  • 0

I know. I was just busting your Muttonchops. It's just what I do.


#2 azrael

azrael

    Member

  • Members
  • 393 posts
  • State:California
  • Country:United States

Posted 09 July 2014 - 12:28 PM

You're in the US, just buy it off McMaster. The proper parts number is in the darts and barrels forum, in the materials list, I believe.
  • 0
Better Nerf By Science!
http://nerfscience.blogspot.com/

#3 rockinon96

rockinon96

    Member

  • Members
  • 142 posts
  • Location:Brasher Falls
  • State:New York
  • Country:United States

Posted 09 July 2014 - 12:37 PM

You're in the US, just buy it off McMaster. The proper parts number is in the darts and barrels forum, in the materials list, I believe.


Ok, thank you, also, Does their 1/2 inch ID 5/8 inch OD Petg tubes fit their 1/2 inch Foam Backer rods? Cause I want to make some #6 slugs.
  • 0

I know. I was just busting your Muttonchops. It's just what I do.


#4 Draconis

Draconis

    I am not Lord Draconical

  • Members
  • 2,712 posts
  • NerfHaven Subscription Supporter
  • Location:Salem, Oregon
  • State:Oregon
  • Country:United States
  • u/Parabolictoys on Reddit

Posted 09 July 2014 - 12:55 PM

The Lee's rigid tubing is not actually PETG, nor do you want the 1/2" size, nor is it available at most chain pets stores in the size you do want. The only places I have found it are small aquarium shops that have the variety display, and Amazon. You want the 9/16" size, as it is labelled for the outside dimension. The 1/2" size is far too small, though it is handy for making dart stops. The bigger drawback is the price. The PETG from Mcmaster is far less expensive, but shipping is ridiculous because of the length. I can't find the 9/16" stuff on Amazon at the moment, but the 5/8" would be similar (and is useful for clear RSCB clips that are CPVC sized). While prime shipping is nice, it ends up being over $3 per foot! My suggestion is to buy from McMaster, but buy it in a larger quantity of tubes than just one.

Amazon: http://www.amazon.co...rds=lee's rigid

Mcmaster: http://www.mcmaster.com/#2044T43 $1.41 + shipping for 48".
  • 0
[15:51] <+Noodle> titties
[15:51] <+Rhadamanthys> titties
[15:51] <+jakejagan> titties
[15:51] <+Lucian> boobs
[15:51] <+Gears> titties
[15:51] <@Draconis> Titties.
[15:52] <+Noodle> why is this so hard?

#5 Thorn

Thorn

    Member

  • Members
  • 91 posts
  • Location:San Diego
  • State:California
  • Country:United States

Posted 09 July 2014 - 12:57 PM

Ok, thank you, also, Does their 1/2 inch ID 5/8 inch OD Petg tubes fit their 1/2 inch Foam Backer rods? Cause I want to make some #6 slugs.

The number for the actual PETG is 2044t43. The 1/2 x 5/8 tubes are actually polyester. But yes, their foam does fit in both PETG and polyester.
  • 0

#6 Sam-underscore

Sam-underscore

    Member

  • Members
  • 89 posts
  • Location:Panhandle Area
  • State:Texas
  • Country:United States

Posted 09 July 2014 - 01:31 PM

Ok, thank you, also, Does their 1/2 inch ID 5/8 inch OD Petg tubes fit their 1/2 inch Foam Backer rods? Cause I want to make some #6 slugs.

If you're looking for some foam, I'd suggest Drev's :D
  • 0
You want Homemades? I make Homemades.
~le yootoob

#7 rockinon96

rockinon96

    Member

  • Members
  • 142 posts
  • Location:Brasher Falls
  • State:New York
  • Country:United States

Posted 09 July 2014 - 02:15 PM

Thank you all for the help. I am just confused as to where to find the foam at McMaster. there is a 3/8 inch backer rod, and a 5/8 inch one.
  • 0

I know. I was just busting your Muttonchops. It's just what I do.


#8 Thorn

Thorn

    Member

  • Members
  • 91 posts
  • Location:San Diego
  • State:California
  • Country:United States

Posted 09 July 2014 - 02:26 PM

Thank you all for the help. I am just confused as to where to find the foam at McMaster. there is a 3/8 inch backer rod, and a 5/8 inch one.

If you had just looked at Ryan201821's thread on how to make darts you would see that it is 93295K33 for 20' of 1/2 FBR and 93295K43 for 250'.
  • 0

#9 rockinon96

rockinon96

    Member

  • Members
  • 142 posts
  • Location:Brasher Falls
  • State:New York
  • Country:United States

Posted 09 July 2014 - 07:14 PM

I did look at that thread, I just must have gone over it by mistake.
  • 0

I know. I was just busting your Muttonchops. It's just what I do.


#10 Naturalman7

Naturalman7

    Member

  • Contributors
  • 158 posts
  • Location:Boise, Idaho
  • State:Idaho
  • Country:United States

Posted 10 July 2014 - 01:15 PM

Foam: 93295K43
Barrels:
Posted Image
  • 0


0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users