Jump to content


Photo

Firestrike Swappable Inline Clip Mod


9 replies to this topic

#1 CRCL

CRCL

    Member

  • Members
  • 18 posts

Posted 26 February 2013 - 03:25 AM

Aim:

Basically to ‘tune up’ the Firestrike and give it a swappable inline clip system to dramatically increase it’s DPS, whilst keeping it as stock looking as possible. Since I'm an Australian nerfer, and have access to slightly different materials to work with I've included some alternative materials to the ones I've used.

Materials:

1x Firestrike (I used the Australian version, but any should do)
1x SGNerf 8kg Retaliator/Rampage replacement spring (or any suitable replacement spring)
1x 20mm UPVC electrical conduit coupler (could be substituted for a 1/2" PVC coupler instead)
1x Papermate ball point pen (almost any pen will do)
16mm UPVC thin-walled (grey) electrical conduit (could be substituted for 1/2" CPVC instead, 17/32" brass could be substituted for the barrel)
20mm UPVC thin-walled (grey) electrical conduit (could be substituted for 1/2" PVC instead)
20mm UPVC thick-walled (orange) electrical conduit (could be substituted for 1/2" PVC instead)
2mm brass rod (a small nail could be used instead)
Etape
Epoxy
Superglue
White lithium greese
Plumbers goop

Tools:

Dremel
Pipe Cutter
Screwdriver
Various knives (I used a hobby scalpel and a swiss army knife)
Needle Nosed Pliers
File
Sandpaper
Pinvice (a drill with a small drill-bit would suffice)

Disassembly:

Remove all the shell screws and open it up. All the screws seem to be the same, so you don't need to keep them in any kind of order. Try not to lose this little nut that holds the battery door on. Put it aside in a safe place.
Posted Image

AR Removal and clip reciever:

Grab your main assembly and pull it apart.
Posted Image
Posted Image

Firstly you need this piece that contains the AR and acts as the plunger-tube cap.
Posted Image

Use a knife to pry it open at the seem. It's not glued together so it should just come apart.
Posted Image
Posted Image
Posted Image

These are what we want. Discard the air restrictor.
Posted Image

Start with the dart post piece (from now on Piece 1). Cut the 6 pieces of plastic holding the dart post to the main ring and discard the dart post. Using your knife and/or dremel with a sanding piece widen the opening till it's about 22mm in diameter. Set piece 1 away for later.
Posted Image
Posted Image

Next get this piece (piece 2) and using your dremel with a grinding bit remove the centre circle and smooth the inside of the ring. Set piece 2 aside for later.
Posted Image
Posted Image

Finally grab the barrel piece and cut off the barrel leaving only the base ring and the plunger-tube 'clips'. Use your dremel with a sanding bit to widen the centre of the ring until it's about 22mm in diameter. Set piece 3 aside for later.
Posted Image
Posted Image

Now grab a small piece (~50mm) of 20mm thickwall (orange) UPVC electrical conduit. Wrap it in E-tape until it fits snugly into piece 2, then epoxy it in place.
Posted Image

Next epoxy piece 1 onto piece 2 as shown.
Posted Image

Final piece 3 gets epoxied on top of piece 1 and 2 as shown. Now piss off for a couple hours and let the epoxy dry.
Posted Image

Cut and/or sand the 20mm conduit flush with piece 2 on the plunger-tube side of the combined piece 1, 2 & 3 (now known as PT-cap); also cut the E-tape that is protruding from the PT-cap off (sorry forgot to take a photo of this).
Posted Image

Next you'll need your 20mm UPVC electrical conduit coupler. Use your dremel to sand the inside of the coupler; you want to get rid of the centre 'ridge' and widen the coupler ever so slightly. You'll know you're done when you can just twist the whole coupler over 20mm conduit with your hands.
Posted Image Posted Image
Posted Image

Next you'll need your coupler and PT-cap. Measure and mark the coupler 28mm from one end. On your PT-cap find where the 20mm UPVC protrudes from piece 3 of the PT-cap, then measure and mark 6mm from this point. Once the measurements are done cut and smooth both pieces; the smaller piece of coupler won't be needed and can be discarded.
Posted Image
Posted Image
Posted Image

Next you'll need a small piece (~50mm) of 16mm thin-walled (grey) UPVC electrical conduit. Using a dremel, files and/or sandpaper sand down the outside of the 16mm UPCV until it can be jammed into the 20mm UPVC stub in the PT-cap. Once it has been sanded down enough to fit, use plumbers goop to glue the 16mm UPVC into the 20mm UPVC leaving an overhang of 16mm UPVC on both sides of the PT-cap. Leave this piece for a few minutes to bond.
Posted Image
Posted Image

Next cut and sand the 16mm UPVC so that it is flush with the 20mm UPVC on both sides of the PT-cap.
Posted Image

Next you'll need your cut down 20mm coupler, the PT-cap, some 2mm brass rod and a pinvice with a 2mm drill bit.
NOTE: Most of you miniature hobbyists will have a pinvice and brass rod lying around for pinning resin/pewter models, but if you don't have either and don't want to buy one; a drill with a small drill bit and a small nail will do.
Posted Image

Now dry-fit your coupler to the UPVC nub of the PT-cap and use your pinvice to drill a hole through the coupler and the UPVC nub then back out the other side as shown. Make sure the brass rod will fit through the holes. Posted Image
Posted Image

Edited by CRCL, 26 February 2013 - 04:14 AM.

  • 0

#2 CRCL

CRCL

    Member

  • Members
  • 18 posts

Posted 26 February 2013 - 03:27 AM

Next measure and cut a 24mm piece of 2mm brass rod. this piece should be the tiniest bit smaller than the diameter of the coupler.
Posted Image

Now that all the pieces fit together nicely, epoxy the coupler to the PT-cap and then roll the brass rod in epoxy and stick it through the holes drilled for it as shown. The brass rod serves two purposes; firstly it anchors the coupler and the PT-cap together ensuring a very strong join and secondly it acts as a dart-stop.
Posted Image

Finally epoxy the Pt-cap onto the plunger-tube as shown. Leave this piece to dry for a few hours. Congratulations you now have a receiver for your inline clips!
Posted Image

Spring Addition:

For the next part you'll need the Plunger-rod assembly. You should probably remove the catch spring and store it somewhere safe, as this next part involves lots of violence and cussing.
Posted Image

I didn't want to cut the plunger-rod to remove the spring, so I copied some of the other Firestrike mods and just twisted the spring off the plunger-rod using a pair of needle-nosed pliers. The hardest part is getting the tip of the spring off the plunger-rod, once you've done that the spring can be easily twisted off. The pictures explain the techniques better than text can.
Posted Image

From Left to right we have a stock Firestrike spring (Australian version) followed by a stock Nitefinder spring and finally the 8kg SGNerf Retaliator/Rampage spring. I only used the SGNerf spring, but since it's a thin spring you could probably also keep the stock spring as well.
Posted Image

The new spring went on the same way the old one came off.
Posted Image

Once you're done put the catch spring back on and you're all done. I found that the stock catch spring was plenty strong enough to keep the blaster primed, even with the upgraded spring.
Posted Image

Shell mods and barrel straightener:

First you'll need the front barrel cover, which looks like this:
Posted Image

Firstly you want to use your dremel with a cutting disc to cut off the front 'barrel cover' till it is about flush with the rest of the piece. Then switch your dremel to a sanding bit and neaten up the front of the piece. Next you're going to want to widen the 'barrel opening' till it can just fit a piece of 20mm UPVC electrical conduit through it. Take your time as this hole needs to be centred as it acts as a guide to keep your barrel straight, you also don't want to make it too wide otherwise the barrel will have 'wiggle room' and won't stay straight.
Posted Image Posted Image
Posted Image
Posted Image

The next couple of steps are just sanding the shell to accommodate the new PT-cap, it's easier to just refer to the following before/after pictures to see what to sand down rather than me typing it out.
Posted Image
Posted Image
Posted Image
Posted Image
Posted Image
Posted Image
Posted Image
Posted Image

The final shell mod will require a Papermate ball point pen. Remove the tip and the ink tube-thing, then cut a small (~10mm) piece of the pen shell. Sand one side of this tube to be slightly angled as shown.
Posted Image

Next Just superglue the small nub of pen Over the back screw-port just under the catch. This stops part of the catch bending when you pull the trigger. This mod isn't essential if you haven't upgraded the catch spring, but I may do an extra spring edition & catch spring replacement down the road.
Posted Image

Reassembling the blaster:

The blaster goes together the same way it came apart, the only difference was that I didn't bother adding the red dot sight to the blaster. If you wish to keep the RDS all you have to do is cut off the piece that goes over the screw-port (sorry I forgot to take a picture).

The hardest part about reassembling the blaster is getting the spring to sit on the spring rest. I left the plunger-tube and plunger-rod till last and then, with the help of some pliers wrestled them in and closed the blaster up.
Posted Image Posted Image
Posted Image

Making the clips:

My 'clips' will be made for use with small 25mm long silicone tipped darts. If I want to use different dart sizes or types I can just alter the design to compensate.

The first thing I made was a singled barrel. All I'm gonna post up are the design and the finished product as it's stupidly easy to make.
Posted Image
Posted Image

The second 'clip' I made was a four dart inline clip. I followed the standard Inline clip design with one slight difference. As the whole clip will be removed I added a small (5mm) piece of 16mm UPVC to the back of the clip. This piece of UPVC was beveled on one side, because the UPVC has a tight fit on darts and because of the bevel on the outer side it is very easy for darts to enter the clip (ie: from you loading them in) and very difficult for the darts to fall back out of the clip (whilst the clip is in your pocket). What this means is you can make multiple clips and store them in your pockets/kit for quick reloads during a match. It also means you can always have a full clip ready in your blaster whilst reloading another.
Posted Image

All done.
Posted Image


EDIT #2: Success! This writeup is a little cut-down, but I hope it suffices.

Edited by CRCL, 26 February 2013 - 04:17 AM.

  • 0

#3 Jeo

Jeo

    Red Team: HooRah!

  • Members
  • 93 posts

Posted 26 February 2013 - 04:11 AM

That's a really nice write up and an especially awesome first post. Mad skills.
  • 0

#4 F man 47

F man 47

    Member

  • Members
  • 11 posts

Posted 26 February 2013 - 06:14 AM

That's a really nice write up and an especially awesome first post. Mad skills.


Nevermind

Edited by F man 47, 26 February 2013 - 06:15 AM.

  • 0

#5 F man 47

F man 47

    Member

  • Members
  • 11 posts

Posted 26 February 2013 - 06:16 AM

Question, is there a screw on the front of the plunger? If there is not, how did you take off the catch?

Anyway, Nice job!
  • 0

#6 The2ndBluesBro

The2ndBluesBro

    Member

  • Members
  • 576 posts

Posted 26 February 2013 - 08:57 AM

Question, is there a screw on the front of the plunger? If there is not, how did you take off the catch?

Anyway, Nice job!


He didn't remove the catch, and in the writeup he says clearly that he unwound the spring and twisted the new one on to change the spring.
  • 0

Nerf, Gaming, knives: https://www.youtube....FjcObRZTl2KReDQ

 


#7 thebob13666

thebob13666

    Member

  • Members
  • 29 posts

Posted 26 February 2013 - 01:07 PM

So I'm guessing the singled barrel will be a pretty significant improvement, but how does the inline clip perform with that small of a plunger tube. What I'm trying to say is, "Ranges?"
  • 0

#8 CRCL

CRCL

    Member

  • Members
  • 18 posts

Posted 28 February 2013 - 08:29 AM

Sorry it's taken so long to reply, I've been a bit busy with uni. Here's a bit of an update on the original post(s) addressing some things I forgot in the write-up.

Updates:

If you wish to keep the flashlight all you need to do is cut a small piece of one of the 'screw port anchors'. It should fit in fine after this.
Posted Image
Posted Image

More clips!
Posted Image

Size comparison with a 12 dart Elite clip:
Posted Image

I forgot to mention that when you mod the PT-cap, the padding on the plunger-head still works and you also add a few millimeters of draw to the plunger-tube (every little bit helps!).

Also because of the clever design of the plunger-head and the fit of the O-ring I found I was getting 100% airseal, so I didn't bother adding E-tape under the O-ring.

Question, is there a screw on the front of the plunger? If there is not, how did you take off the catch?


As The2ndBluesBro pointed out, I didn't take the plunger-rod apart at all. You could cut off the clip that holds the plunger-head on and then replace it with a screw if you want to disassemble the plunger-rod.

Range Test:

NOTE: This was a very rough range-test, I'm going to do a more accurate test with more data when I have some more time and it's not hotter than the centre of the sun outside.

Inline clips 50-60 feet. (4 shots)
Singled clip 55-60 feet. (3 shots)

The inline clips don't give inspiring ranges, but they're not that bad considering the rate of fire. I'm guessing the singled clip performed so badly because I foolishly gave it the same barrel length as the inline clips (100mm). I'm going to make a 150mm one and test it out, hopefully I can test it and cut it down till I reach an ideal length.

Rate of Fire test:

I performed this test by just timing how long it took me to fire off 8 darts, I had the darts or clips sitting on a nearby counter. Again it's a rough test just to give you an idea of the improvements, I'll post up a more accurate one at a later time.

Firestrike (stock): 28 seconds to fire 8 darts (I fumbled a bit with one dart, which probably added a second or two to this time).
Triad (stock-ish): 14 seconds to fire 8 darts.
Firestrike (2x Inline clips): 9 seconds to fire 8 darts.
  • 0

#9 Blue

Blue

    Member

  • Members
  • 2,222 posts

Posted 13 March 2013 - 02:03 PM

I like what you did with the piece of pen to thicken the screw ports so that the catch doesn't flex.
  • 0

#10 CRCL

CRCL

    Member

  • Members
  • 18 posts

Posted 29 April 2013 - 10:02 AM

Just as a quick update, before I go to sleep and forget:

I've found that the SGnerf 10kg Swarmfire upgrade spring is a much better fit than the 8kg retaliator/rampage spring for modding the Firestrike. It's a better length, stronger and the stock catch spring is strong enough to hold it.

Also 150mm seems to be giving me the best ranges with the singled barrel and my shorter darts. I also made a 70mm barrel for firing micro and sonic darts.
  • 0


1 user(s) are reading this topic

0 members, 1 guests, 0 anonymous users