Jump to content


Photo

Crossfire Pump-Action Mod

And some other stuff...

3 replies to this topic

#1 hamoidar

hamoidar

    Member

  • Members
  • 367 posts

Posted 29 June 2012 - 02:24 PM

In this mod-guide, I will show you how to make your Nerf Crossfire into a pump-action, medium power...I can't really call it a beast. I started the mod because this broke....
Posted Image
And that meant that I would not be able to use the original slide, for that matter, no slide at all.
The only option would be to make it pump-action, using the same principal as the Nerf clip-system guns.

You will need:
About 10" of 1/2" CPVC
A 2" piece of raider barrel, or any other clip-system gun barrel.
Stampede muzzle.
Hyperfire spring, or equivalent.
Two-part epoxy.
1/2" PVC
Electrical tape.
Screwdriver.
Hack saw.
Drill and bits.

Time to start, first open the gun.
Posted Image

Then remove the dart holder.
Posted Image

Remove the plunger system, the slide, and the catch.
Posted Image

Put the two halves of the gun back together, and cut the shell as pictured;
Posted Image
Posted Image

Take a 3.5" piece of 1/2" CPVC, and wrap 5 layers of e-tape 1/4" from the end.
Posted Image

Oh, and you can discard all of the original dart tube parts except the o-ring.
Posted Image

Using a bit of super-glue, attach the o-ring to the end of the CPVC.
Posted Image

Cut off the excess CPVC.
Posted Image

Using a 2in piece of clip-system blaster barrel, and epoxy, connect another 3" piece of CPVC to the first one.
Posted Image

Take your Stampede muzzle and cut off all the stuff shown;
Posted Image
Posted Image

Then hollow out the front of the gun until the Stampede muzzle fits snugly.
Posted Image

Epoxy the muzzle into ONE side. (the side with the trigger)
Posted Image

Test fit the barrel in the muzzle. The barrel should slide freely.
Also, slide the plunger tube onto the back of the barrel assembly.
Posted Image

Pull the plunger tube back until the catch face is where it would be if the gun were cocked, and pull the barrel forward until the o-ring almost comes out. Take a small sliver of 1/2" PVC, and screw it onto the barrel, flush with the edge of the stampede muzzle.
Posted Image

Instead of the stock spring I used a Hyperfire spring; which barely fits, but is much stronger.
Posted Image

I use white lithium grease for all my guns, and this one is no exception.
Posted Image

To reduce dead-space, I glued a 4" piece of Nylon rod with a 1/4" hole drilled through it, into the barrel.
Posted Image

I added a piece of 1/2" PVC on the tip of the barrel, in hopes of adding a hopper. But the gun's tiny plunger tube could not supply the necessary volume of air for the hopper.
Posted Image

I plan on adding a CPVC coupler and a speed-loader, but for now, the gun is a single shot muzzle-loader.
Posted Image


The gun gets around 40-45ft flat with Mysterios dARts.

Questions? Comments? FLAMES?

Edited by hamoidar, 29 June 2012 - 02:26 PM.

  • 0
NerfHaven > Your control panel > Profile > Change Signature > Inserts dumb sig > What! No pictures! > Inserts next best thing: http://nerfhaven.com...howuser=114052' class='bbc_url' title='External link' rel='nofollow external'>Best thing on Nerfhaven!

#2 BMSCmods

BMSCmods

    Member

  • Members
  • 19 posts

Posted 29 June 2012 - 03:03 PM

I thought that blaster was called a Strikefire????Oh well. Very nice mod and very clean cuts! EDIT: The blaster can be called both the nerf crossfire and nerf strikefire I checked on Google Images

Edited by BMSCmods, 29 June 2012 - 03:05 PM.

  • 0

#3 Bow n Arrow

Bow n Arrow

    Member

  • Members
  • 2 posts

Posted 29 June 2012 - 08:15 PM

Nice mod! I was wondering if you could use stock Nerf darts as well as dARts?
  • 0
“Size matters not. Look at me. Judge me by my size, do you?" -Yoda

#4 hamoidar

hamoidar

    Member

  • Members
  • 367 posts

Posted 29 June 2012 - 08:19 PM

Nice mod! I was wondering if you could use stock Nerf darts as well as dARts?

Well, in this gun, the dead-space-removing Nylon rod comes almost to the front of the barrel, leaving only about 1.5". But if you were to cut the rod a bit shorter, stock darts would fit fine.
  • 0
NerfHaven > Your control panel > Profile > Change Signature > Inserts dumb sig > What! No pictures! > Inserts next best thing: http://nerfhaven.com...howuser=114052' class='bbc_url' title='External link' rel='nofollow external'>Best thing on Nerfhaven!


0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users