Jump to content


How to make Rayven trigger pull easier?

a Mod request

5 replies to this topic

#1 AbstractSociety



  • Members
  • 108 posts
  • Location:Los Angeles, California
  • State:California
  • Country:United States

Posted 04 May 2012 - 02:31 AM

Is it possible to make the Rayven trigger pull easier, and if so, how? The trigger pull is something that bothers me quite a bit. If someone could make a guide it would be greatly appreciated!

Edited by AbstractSociety, 04 May 2012 - 02:32 AM.

  • 0

#2 Xellah


    They call his chin.... Captain Underpants

  • Members
  • 178 posts
  • Location:Columbus, OH 43201
  • State:Ohio
  • Country:United States

Posted 04 May 2012 - 04:04 AM

The trigger pull is awful on the Rayven and causes jams, misfires, etc. Here's my solution:

Posted Image

I haven't seen this done before, but I'm sure that it's not an original idea. I replaced the compression spring on the pusher mech with an extension spring that is screwed to the shell. I only used a dab of high temp hot glue to attach the spring to the pushing arm, but even after dozens of our weekly wars it hasn't shown signs of coming off.

I don't recommend hot glue. Fastening with a screw is superior. I've left mine this way to stress test it to see if the bond would break. Here's the spring action as you pull the trigger:

Posted Image

The pull on an extension spring is much smoother than compressing the stock spring. I got this extension spring from a small spring pack I bought from Home Depot a while back. The key is to find a spring weak enough to have a smoother trigger pull, but strong enough to completely retract the pushing arm. Otherwise, the arm will block the next streamline in your magazine from seating itself in front of your pusher, like so:

Posted Image

^ This is bad. Check to make sure your arm is full retracted by your replacement spring before closing your blaster up.
  • 0
Ultimator Duel

it cant be as bad as reloading an ak-47 on the run

#3 Langley


    LGLF - Since 2002

  • Administrators
  • 2,995 posts

Posted 04 May 2012 - 08:53 AM

Is this a common problem? I've only used mine in a couple of wars, but I don't think I've ever had this problem with the trigger.
  • 0

You can poop in my toilet anytime champ.

2016 Nerf War Schedule
Bless you, my son. Now recite 3 New Members Guides and 5 Code of Conducts for your sins.

#4 Guitarzan



  • Members
  • 133 posts
  • Location:Apalachin, NY , 13732
  • State:New York
  • Country:United States

Posted 04 May 2012 - 11:52 AM

Is this a common problem? I've only used mine in a couple of wars, but I don't think I've ever had this problem with the trigger.

I haven't really been able to identify why, but it varies from gun to gun. I've owned two of them so far. One of them had an extremely difficult trigger pull that actually gave me finger cramps if I tried to do any sort of rapid fire. The other had a smooth trigger pull.
  • 0

#5 SpokkyLucaz



  • Members
  • 72 posts
  • State:California
  • Country:United States

Posted 04 May 2012 - 10:29 PM

I've had the exact same issue with mine. I can NOT stand the stock trigger pull(some may wonder 'what are you talking about??') and seeing as how the rayven is a naturally moody blaster, my trigger pull was harder than a stock barricades.
What I did to combat this and keep the upcoming dart from locking the dart pusher in place was removing the stock trigger spring and placing a return spring wrapped around the trigger lever and a dart post. Here are some pics to display as to what I mean:
Posted ImagePosted Image
Posted ImagePosted ImagePosted Image

(Sorry for shitty quality...best I could do with my webcam and 4 lamps <_< )
  • 0
Active HVZ participant.

I can tell you right now, with certainty, that none of you greasy fucks are laying your filthy paws on my blaster and it sure as fuck isn't going in a plastic orgy pile with other plastic guns.

#6 Darthrambo



  • Members
  • 116 posts

Posted 05 May 2012 - 05:55 PM

The trigger pull is kinda hard since the shorter trigger pull is being converted into a longer pusher arm draw by the lever going from the trigger to the metal arm.

You can swap out the return spring with something lighter but that will make the return motion weaker and if its too weak it can make it so the friction of the arm on the next dart can jam it up.

Maybe try making sure everything is lubed up and possibly seeing of loosening the screw that holds the lever to the metal arm helps at all.

Removing the trigger lock might get rid of a little of the resistance too.
  • 0

0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users