Jump to content


Photo

Gotcha Shot

Now with 100% more Nitefinder internals!

5 replies to this topic

#1 VelveetaAvenger

VelveetaAvenger

    Member

  • Members
  • 630 posts

Posted 25 January 2011 - 04:17 PM

I was at Tuesday Morning last week and picked up a neat looking gel-blaster called the "Gotcha Shot". While it was fun to mess around with (emphasis on the mess, the goo likes to dribble all over and according to the package will stain your clothes if you actually get shot with it) I prefer to fling foam, not gib with gel. After cracking it open it was pretty obvious that slapping a coupler on and calling it a day wasn't an option. Internal shots from an earlier form of this blaster can be found HERE if you want to know what got removed.

The original plan was to make a homemade plunger tube/rod/head, but I had a spare Nitefinder sitting around so I just raided that. The first step, after opening the Gotcha Shot, was to clear out all the junk inside. Everything except the catch, spring, and trigger went straight into the garbage. Fortunately, the catch isn't actually attached to anything, so you don't even have to cut it off.

Next break out the dremel! I highly recommend getting a "high speed cutting" bit, it's all I use anymore.
Posted Image
Everything that holds the original internals should be cleared away, except for the rearmost wall. It's a convenient brace for the Nitefinder plunger tube. This is where I made the biggest mistake of this mod. The rectangle that is cut away from the shell was raised up and flat, from eyeballing the plunger tube fit it looked like it had to go. When I finished both sides and put it together, the plunger tube was loose and rattling around. Fortunately the problem was easily solved with a few layers of electrical tape, but the moral of the story is that cutting twice and measuring once is completely wrong!

Look at that plunger rod action!
Posted Image
The pump length on the Gotcha Shot is about 3 inches, but the Nitefinder rod is just long enough to cover it. I ended up cutting it under a 1/4 inch from the priming handle, but you'll want the rod to be as long as possible and trim it down to fit. Make sure to trim down the Nitefinder catch as well, so it doesn't get hung up on that bracing wall. Then use goop to attach the rod to the catch. I just measured the draw of a stock Nitefinder, and was surprised to find that it is apparently only 1.75 inches, so there's definitely an air volume increase. The spring is also stronger then a stock Nitefinder spring, I don't have any of the popular replacements to compare it to though.

Now it's time to get the tube in there!
Posted Image
It's so close to being a perfect fit length-wise. At first I just trimmed the tiniest bit off the back end, under an 1/8th of an inch. When it became apparent that it was too loose to just sit in the shell, I got out the Gotcha Shot's original "barrel" to stabilize it in front. The plunger tube won't fit inside the barrel, but it's close enough that you can widen the inside of the barrel without cutting through. Goop them together, wrap e-tape to stabilize the back, and it sits in there quite solidly.

Looking good so far!
Posted Image
It's a half cpvc 1/2 inch coupler, gooped into the hollowed out thing that holds the Nitefinders A/R, which is gooped to the plunger tube and Gotcha Shot "barrel". Although I did this last, I would recommend doing it before trimming the plunger tube. When I fit it on the plunger tube normally, it was too far in and the plunger head knocked it off after a couple of test shots. In the picture it is attached a little bit further out, but is holding together so far. It is completely airtight, when I hold my hand over the coupler the plunger stops with about 1/3 of the tube left.

All together now!
Posted Image
The finished product. It shoots across my living room and into the hallway wall without losing any height. I think that's something like 35-40 feet. An outdoors test doesn't really matter at this point, since it's below freezing with a couple feet of snow on the ground, but it should get comparable ranges to any draw-extended Nitefinder. It's a really comfortable and cool looking shell, I wish I hadn't cut those rectangles out of it though.

I'd like to set up a breech that opens when the pump moves back and closes when it moves forwards again, but I'm not sure how to do it without adding a ton of dead space. Do breeches still work if you push the dart behind the opening instead of in front of it?

Anyways, that's all for now. Hope you guys enjoy the mod/writeup, I was just glad to find a project that interested me over the winter here.

↓ Haha. Yeah, I scraped off the "DO NOT" part.

Edited by VelveetaAvenger, 25 January 2011 - 04:48 PM.

  • 0
"I never saw Beastmaster, I just wanted to be cool..."

#2 NerfHunter03

NerfHunter03

    Member

  • Members
  • 89 posts

Posted 25 January 2011 - 04:42 PM

Nice writeup. Did you trim/sand anything off the outside of the shell? From the last picture you took, it almost seems the blaster IS telling you to "shoot anyone in the face or eyes" ... Am I missing something here?

Edited by NerfHunter03, 25 January 2011 - 04:43 PM.

  • 0
BritNerfMogul:
QUOTE
We should respect the people who make our blasters. Even if we do molest the hell out of them...

#3 blitz

blitz

    Member

  • Members
  • 285 posts

Posted 25 January 2011 - 08:22 PM

Very, very cool.... if only I had money.....
  • 0
Blitz, member of the FNBS
"sexual innuendo no intendo"

#4 sodizzle3113

sodizzle3113

    Member

  • Members
  • 66 posts

Posted 25 January 2011 - 09:40 PM

Nice writeup. Did you trim/sand anything off the outside of the shell? From the last picture you took, it almost seems the blaster IS telling you to "shoot anyone in the face or eyes" ... Am I missing something here?

That's what I was thinking...

Anyway, nice writeup. Do you think this could be done with something like an LS plungertube?
  • 0

#5 VelveetaAvenger

VelveetaAvenger

    Member

  • Members
  • 630 posts

Posted 25 January 2011 - 10:37 PM

Thanks for the positive responses!

Anyway, nice writeup. Do you think this could be done with something like an LS plungertube?


I don't have a Longshot plunger tube at the moment, but maybe. Like I said, the way I cut it the Nitefinder tube is really loose in the shell. It would be possible to cut the sides out further as well. Fortunately, the tube isn't glued to the blaster, and Longshot/Nitefinder plunger heads are interchangeable on the Nitefinder plunger rod. So upgrading in the future would be easy, if the tube does fit in the shell.

The only reason I might not use a Longshot plunger tube is that while the 3 inch draw pushes the Nitefinder tube to its limits, you'd have to cut down a Longshot tube you could be using in a different blaster that can take full advantage of it.

Edited by VelveetaAvenger, 25 January 2011 - 10:42 PM.

  • 0
"I never saw Beastmaster, I just wanted to be cool..."

#6 Exo

Exo

    Member

  • Members
  • 391 posts

Posted 25 January 2011 - 10:44 PM

Nice. I was just griping the other day that no one modded any unusual or uncommon guns the other day. It's kind of like a mini-overhaul. It looks like it might be Raider-style primed. Very nice pseudo-writeup.
  • 0


0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users