Jump to content


Photo

Full Cpvc Clip Accepting Ls Breech

Dizzle Breech?

20 replies to this topic

#1 sodizzle3113

sodizzle3113

    Member

  • Members
  • 66 posts

Posted 02 December 2010 - 06:50 AM

Improvemants are farther down the page!


I don't have access to the different sizes of brass needed to make an Angel Breech, and I don't have enough money to buy off the internet. So I searched all over for a cpvc breach. I found two, both of which needed brass, I found http://www.nerfrevol...c.php?f=8&t=631 louiec3's breech and Uin13/Ice's breech. I also knew about singling it but, did not want to lose the ROF. So I went to work:

Materials:
1/2" CPVC
1/2" Cpvc Coupler
Thinwalled 1/2" PVC
Hotglue
super glue
Dremel
sand paper

First off let me tell you that the pictures came from 2 different longshots so if the colors of the peices change that is why

Here is the finished project:
Posted Image
I tried to make it as stock looking as possible.

First off take apart the blaster (no duh!)
then take this piece (the black one in the picture I don't remember what it is called) and cut it off.
Posted Image

Take only the bottom circle (orange in this picture) and put about 2 or 3 feet (enough to let it stick out the end of the blaster if you were to assemble it) Make sure to put that O-ring back on
Posted Image

then fill in the dead space with hotglue
Posted Image

when plunger setup is assembled it should be around this long
Posted Image

next, make your marks on where to cut the cpvc. (it needs to be small enough to completely fit inside the coupler but large enough to keep the dart from advancing too far in the clip. It also needs to be stategically placed to where when the plunger rod is caught by the catch the front mark is ontop of the dart and the back mark is behind the dart.) This is vitally important, if this is done incorectly it is highly likely it will not work in the end.
Posted Image

Then make a smooth line to cut like shown in the picture below
Posted Image

Make sure it will fin in the coupler. (in this picture it is too large so I had to make it a little smaller)
Posted Image

Next take your coupler and look inside it, you will find a ridge to stop the pipe from moving too far.
Posted Image
now sand the ridge off.
Posted Image

After you made sure that it fits inside the coupler go ahead and cut along the smooth line you made earlier
Posted Image

(I did not take a picture of this step so I will try to explain it as best as I can) After you have the cpvc in find where it rests all of the way forward. Hot glue the sanded out coupler with the other part of the cpvc glued inside of it.
(crude picture drawn in paint)
Posted Image

With the blaster assembled find where the nub should be super glued on. (I used goop, superglue, and epoxy to keep it on.)
Posted Image

then take your pvc cut it in half length wise and make it long enough to make it from the coupler to the front of the clip.
Posted Image

after you glue on the nub take some test shots to make sure it works and your done!

Posted Image

Edited by sodizzle3113, 22 December 2010 - 12:44 PM.

  • 0

#2 sodizzle3113

sodizzle3113

    Member

  • Members
  • 66 posts

Posted 02 December 2010 - 06:52 AM

Edit:
Pictures of the finished breech.
closed
Posted Image
opened
Posted Image
closed with blaster opened
Posted Image
opened with blaster opened
Posted Image

Edit: added video
Video
  • 0

#3 Kid Flash

Kid Flash

    Member

  • Members
  • 1,985 posts

Posted 02 December 2010 - 01:56 PM

Pretty neat design. I'm going to assume that there's not enough length for streamlines though, right? Anyways, it looks clean (on the outside), so good job.
  • 0

#4 sodizzle3113

sodizzle3113

    Member

  • Members
  • 66 posts

Posted 02 December 2010 - 02:53 PM

No, it doesn't accept streamlines. Streamlines are too tight to fit in my cpvc anyway. I'm working on a design for one to accept streamlines, but it will take a lot of sanding.
  • 0

#5 knexpert66

knexpert66

    Member

  • Members
  • 133 posts

Posted 02 December 2010 - 04:30 PM

Crap! I was thinking about posting something almost exactly like this. Thats fine though. It was a pain in the neck.

Edited by knexpert66, 09 February 2011 - 08:38 PM.

  • 0
Please, call me Busted.

#6 sodizzle3113

sodizzle3113

    Member

  • Members
  • 66 posts

Posted 02 December 2010 - 04:58 PM

Crap! I was thinking about posting something almost exactly like this. Thats fine though. It was a pain in the ass.

If you are worrying about being "first" I already had this up on nerfrevolution a few months ago. I even have improvements up on Nrev, I'll be posting that here soon.
  • 0

#7 Nerfer 91

Nerfer 91

    Member

  • Members
  • 20 posts

Posted 02 December 2010 - 05:39 PM

Very nice job!

I might do this except replace the coupler with half in. repair brass... Im deciding over a new design of a clip accepting e pic longshot or this.

Edited by Nerfer 91, 02 December 2010 - 08:48 PM.

  • 0
"85% of teens would cry if they saw Justin Beiber standing on top of the Willis Tower, about to jump. If you're one of the 15%% who would sit there eating pop corn and laughing while screaming "Jump or ill come push you off faggot" Post this as your signature."

#8 knexpert66

knexpert66

    Member

  • Members
  • 133 posts

Posted 03 December 2010 - 04:26 PM

Crap! I was thinking about posting something almost exactly like this. Thats fine though. It was a pain in the neck.

If you are worrying about being "first" I already had this up on nerfrevolution a few months ago. I even have improvements up on Nrev, I'll be posting that here soon.

Yeah, My idea was failing anyway.

Edited by knexpert66, 09 February 2011 - 08:39 PM.

  • 0
Please, call me Busted.

#9 Abyss Mods

Abyss Mods

    Member

  • Members
  • 205 posts

Posted 03 December 2010 - 05:23 PM

RIGHT after I finish my singled LS. <_< Very neat design. I would make this, but I don't have another LS to perform this mod on.
  • 0

#10 HasreadCoC

HasreadCoC

    Member

  • Members
  • 274 posts

Posted 03 December 2010 - 08:44 PM

The truly genius part of this (if I understand it correctly) is that you can have proper barrel length (as in, not the usual 2in barrel) the same as you would with a singled LS, but this way it still takes clips. Great work dude, now I wonder if this can be done to a recon? I'd make the assumption that it would, but you know what they say about assumptions.....
  • 0

I'm the only respectable person here. The rest of the NIC are pretty much just child molesters.


AKA: ObiWonTwo on Nerfrevolution, and most of the rest of the internet for that matter.....

#11 sodizzle3113

sodizzle3113

    Member

  • Members
  • 66 posts

Posted 21 December 2010 - 06:23 PM

I don't know if this would be considered a necro but whatever. I have improvements I have done to this mod and I don't know if I should start a new thread or post it here.
  • 0

#12 iDrag0m1r

iDrag0m1r

    Member

  • Members
  • 66 posts

Posted 22 December 2010 - 10:03 AM

Just post them right here and put it in the first post that there are improvements further down the page.
  • 0
I AM JUNIOR!

#13 sodizzle3113

sodizzle3113

    Member

  • Members
  • 66 posts

Posted 22 December 2010 - 12:40 PM

I have improvements!

First off, remember that nasty "smooth curve" I made you cut? Well, your life is now easier. There's no need for that anymore because a straight line will do the trick. You can use a dremmel or miter box saw or even ratcheting pipe cutters. DONT FORGET THE SAND THE INSIDE OF THE BREECH OUT!!!
Posted Image
Another thing is stability. Instead of using glue why not use a bolt to attach the nub? You can even leave more of the orange part on the nub and put the bolt in that.
Posted Image
You can also wrap some e-tape around the end of the CPVC that the black (or orange) peice that goes inside the plunger tube goes on. It helps make a better seal and it helps with putting it on there straight.
Posted Image
Posted Image
I still like to use the thin walled (SCH. 20?) pvc for a ramp though.
Posted Image
Now here are some pictures of the finished breech inside the blaster:
Posted Image
Posted Image

Can I call it the Dizzle Breech?

Finished LS
Posted Image

Video:
http://www.youtube.c...h?v=kLcdDSnftiY
  • 0

#14 zander2

zander2

    Member

  • Members
  • 11 posts

Posted 23 December 2010 - 02:18 PM

Nice. What kind of range does it get?
  • 0

#15 socal

socal

    Member

  • Members
  • 30 posts

Posted 23 December 2010 - 03:31 PM

I like the duel triggers but how did you get it to work,plus how comfortable is having to two triggers on that handle. also with this breech can you top load darts if like your clip runs out.

Edited by socal, 23 December 2010 - 03:33 PM.

  • 0

#16 sodizzle3113

sodizzle3113

    Member

  • Members
  • 66 posts

Posted 23 December 2010 - 09:49 PM

I like the duel triggers but how did you get it to work,plus how comfortable is having to two triggers on that handle. also with this breech can you top load darts if like your clip runs out.

It is just like linking the triggers only with a second trigger. It is very comfortable IMO. I like it better than a keyring trigger. It is not that hard to do. It just takes a lot of dremeling.
  • 0

#17 ImportedUniversal

ImportedUniversal

    Member

  • Members
  • 14 posts

Posted 24 December 2010 - 07:59 AM

That's Nice, Man. I Fucked up one of my old Longshots trying to Single it (Somehow), But I have another now. I'll DEFINATELY have to do this.

Quick Question: Can the Sch. 20 PVC be replaced with some of the fake barrel from the LS? I just don't want to buy a ton of thinwall when I'm only going to use an inch or so on this.
  • 0
Ever tried to shove a cactus up your ass? It hurts like hell.

And My primary is an RFR because i like to rub my nipples.

#18 sodizzle3113

sodizzle3113

    Member

  • Members
  • 66 posts

Posted 24 December 2010 - 01:07 PM

That's Nice, Man. I Fucked up one of my old Longshots trying to Single it (Somehow), But I have another now. I'll DEFINATELY have to do this.

Quick Question: Can the Sch. 20 PVC be replaced with some of the fake barrel from the LS? I just don't want to buy a ton of thinwall when I'm only going to use an inch or so on this.

Anything would work as long as the cpvc fits inside of it.
  • 0

#19 WicketTheModder619

WicketTheModder619

    Member

  • Members
  • 247 posts

Posted 24 December 2010 - 02:15 PM

Not meaning to hijack the thread or anything, but I made one of these and thought I would share a little. First off I would like to say, that these are not hard to make. I made mine from a singled longshot I already had, the conversion was pretty simple. I remember there being talk of more powerful springs to get better ranges, so mine has a quadshot and recon spring combo. I am getting ranges of 90-100 ft flat, and I am 14 and can prime it one handed with not too much difficulty. I also made a new method for stefan clips and will have a write-up soon. With these new clips, I haven't had a single jam! You should all make one of these, and credit for mine goes to sodizzle for the concept and write-up.
  • 0
23:06 Buffdaddy: As long as they aren't doing it all night, don't care.

#20 Phibonnachee

Phibonnachee

    Member

  • Members
  • 28 posts

Posted 27 December 2010 - 06:03 PM

Intriguing. Still wondering if this would jam any more often or not be as smooth because it is cpvc and the fit of stefans in cpvc is a lot tighter. Im sure if you used the grey foam bullets then it would be fine but thicker foam don't think would work that well. Also, im curious as to the seal of the bolt, they are sealed simply from contact inside a coupler, which sounds like it might work but having hard surfaces in contact dont normally form tight seals. Also, what springs do you have in there?
  • 0
De-single your longshot Longshot --- 4B magazine breech BBBB

#21 sodizzle3113

sodizzle3113

    Member

  • Members
  • 66 posts

Posted 27 December 2010 - 08:18 PM

Intriguing. Still wondering if this would jam any more often or not be as smooth because it is cpvc and the fit of stefans in cpvc is a lot tighter. Im sure if you used the grey foam bullets then it would be fine but thicker foam don't think would work that well. Also, im curious as to the seal of the bolt, they are sealed simply from contact inside a coupler, which sounds like it might work but having hard surfaces in contact dont normally form tight seals. Also, what springs do you have in there?

I use tighter fitting foam than the grey stuff. I use the white foam that is similar to what split was selling a while back. It seals because of the coupler. The coupler makes he sealbecause it fits over the bolt. I currently have a maverick recon longshot combonation of springs on it.
  • 0


1 user(s) are reading this topic

0 members, 1 guests, 0 anonymous users