Jump to content


Photo

A New Longshot Foregrip Mod

I have never seen this before

14 replies to this topic

#1 thedom21

thedom21

    Member

  • Members
  • 462 posts
  • Location:Saint Paul MN
  • State:Minnesota
  • Country:United States

Posted 26 June 2010 - 08:55 PM

I wanted a way to make a fore grip for my longshot that was easy to do, cheap, and looked somewhat aesthetically pleasing.
I think I have found a way to do this. It happened completely by accident. I was trying to figure out a new mod fore my longshot, something that has never been done before. So as I am looking at my longshot internals I picked up the boltsled and something dropped off my workbench and my brothers dog spooked and scratched the back of my leg. I dropped the bolt sled and went to go "tend my wounds" and when I came back and looked at my gun the bolt sled had landed flipped of its normal position. Then i said "I got it!" and this is what I came up with.

Tools:
Dremel
File
Drill

Supplies:
2 inch PVC
4 small bolts
4 nuts to go on the bolts

Step 1:
Remove the Bi-pod and cut your shell to look like this,
http://s508.photobuc...nt=IMG_4850.jpg[/img]

Note: the hole on the bottom of the shell needs to be 1 1/4 " wide

Next cut the bolt sled shorter so it should look like this,You also have to shave the part where the priming handle goes through that area should be flat. Also those two little black wheels need two be taken out of the bolt sled
http://s508.photobuc...nt=IMG_4859.jpg[/img]

Now set the bolt sled aside and lets start prepping the shell.

Before
http://s508.photobuc...nt=IMG_4733.jpg[/img]

After
http://s508.photobuc...nt=IMG_4735.jpg[/img]

Before
http://s508.photobuc...nt=IMG_4735.jpg[/img]

After
http://s508.photobuc...nt=IMG_4737.jpg[/img]

Note: You need to remove all 3 of the little "walls"


Next, put your bolt sled in like so. It should be able to slide back and forth pretty easily.
http://s508.photobuc...nt=IMG_4746.jpg[/img]

http://s508.photobuc...nt=IMG_4747.jpg[/img]

Next slide the bolt sled all the way back and take your 2" PVC and cut it to 4" long
http://s508.photobuc...nt=IMG_4858.jpg[/img]

Drill two holes in the bolt sled like so,
http://s508.photobuc...nt=IMG_4859.jpg[/img]

Next place the PVC like shown in the picture.

http://s508.photobuc...nt=IMG_4868.jpg[/img]\

Those are my knees by the way however different they might look they are knees.

Mark the PVC with a sharpie like shown,

http://s508.photobuc...nt=IMG_4863.jpg[/img]

Next drill out the two holes in the PVC you just marked

http://s508.photobuc...nt=IMG_4864.jpg[/img]

Assemble the bolt sled and PVC like shown

http://s508.photobuc...nt=IMG_4865.jpg[/img]

http://s508.photobuc...nt=IMG_4866.jpg[/img]

Place in your gun and reassemble the gun. It should look something like so,

http://s508.photobuc...nt=IMG_4870.jpg[/img]

And slide easily

http://s508.photobuc...nt=IMG_4871.jpg[/img]

Questions? Comments? Flames? I am not sure how to post pics directly on the post so if you know how please tell me how.

Edited by thedom21, 26 June 2010 - 08:59 PM.

  • 0
Funny Irc moments

22:32 hookerninja I would just switch to 2 full 69's
22:32 hookerninja that would diddle shit

11:44 Zorn Her butt is too tiny even for limp 6th grade penis?
11:44 Zorn ergo the dildo

#2 Blue

Blue

    Member

  • Members
  • 2,222 posts

Posted 26 June 2010 - 09:00 PM

You take the pictures in your photobucket account and copy paste the IMG tag underneath it here, not sure what you tried.
  • 0

#3 thedom21

thedom21

    Member

  • Members
  • 462 posts
  • Location:Saint Paul MN
  • State:Minnesota
  • Country:United States

Posted 26 June 2010 - 09:11 PM

I will change that later I am to tired to do it right now. Are the pictures working though?
  • 0
Funny Irc moments

22:32 hookerninja I would just switch to 2 full 69's
22:32 hookerninja that would diddle shit

11:44 Zorn Her butt is too tiny even for limp 6th grade penis?
11:44 Zorn ergo the dildo

#4 Foam Ninja

Foam Ninja

    Member

  • Members
  • 185 posts
  • Location:Aurora IN
  • State:Indiana
  • Country:United States

Posted 26 June 2010 - 09:26 PM

Ok something tells me this is going to sound really stupid on my part, but does this thing even fire?!
  • 0
QUOTE(Soothsayer @ Jul 18 2010, 03:51 PM) View Post

Still haven't beat Foam Ninja in a sword fight


QUOTE

1.The baby would blow up do to being made of pure fail.
2.I GIVE UP! I AM GETTING MY GAS ELSEWHERE!!
-Nerf Mafia

#5 thedom21

thedom21

    Member

  • Members
  • 462 posts
  • Location:Saint Paul MN
  • State:Minnesota
  • Country:United States

Posted 26 June 2010 - 09:31 PM

Yes it shoots 100' flat but at that point I didn't have any other internals in it. I brass breached it and improved its seal. ROF is very good actually.
  • 0
Funny Irc moments

22:32 hookerninja I would just switch to 2 full 69's
22:32 hookerninja that would diddle shit

11:44 Zorn Her butt is too tiny even for limp 6th grade penis?
11:44 Zorn ergo the dildo

#6 Foam Ninja

Foam Ninja

    Member

  • Members
  • 185 posts
  • Location:Aurora IN
  • State:Indiana
  • Country:United States

Posted 26 June 2010 - 09:48 PM

Yes it shoots 100' flat but at that point I didn't have any other internals in it. I brass breached it and improved its seal. ROF is very good actually.


Ok I was really confused for a minute there, thanks for clearing that up. Also may I say very nice work, very nice.
  • 0
QUOTE(Soothsayer @ Jul 18 2010, 03:51 PM) View Post

Still haven't beat Foam Ninja in a sword fight


QUOTE

1.The baby would blow up do to being made of pure fail.
2.I GIVE UP! I AM GETTING MY GAS ELSEWHERE!!
-Nerf Mafia

#7 thedom21

thedom21

    Member

  • Members
  • 462 posts
  • Location:Saint Paul MN
  • State:Minnesota
  • Country:United States

Posted 26 June 2010 - 09:52 PM

Why thank you. The internals were not in the gun because the epoxy for my brass breach was drying. It doesn't work now though because I snapped a piece in the plunger tube but am getting one from Modsquad As soon as he responds to my PM's!

Check out my trading thread here
http://nerfhaven.com...showtopic=19742
  • 0
Funny Irc moments

22:32 hookerninja I would just switch to 2 full 69's
22:32 hookerninja that would diddle shit

11:44 Zorn Her butt is too tiny even for limp 6th grade penis?
11:44 Zorn ergo the dildo

#8 SaucyGanzalez

SaucyGanzalez

    Member

  • Members
  • 109 posts
  • Location:Cincinnati Ohio

Posted 27 June 2010 - 11:21 PM

I really like this mod, I just have one question: doesn't the slide get in the way of the dart tooth?
  • 0
"Fuck it, ill use a hacksaw" ~ SaucyGanzalez

"Makin darts, eaten'....What ever this is" ~ UberKuhlMan

#9 SaucyGanzalez

SaucyGanzalez

    Member

  • Members
  • 109 posts
  • Location:Cincinnati Ohio

Posted 27 June 2010 - 11:21 PM

I really like this mod, I just have one question: doesn't the slide get in the way of the dart tooth?
  • 0
"Fuck it, ill use a hacksaw" ~ SaucyGanzalez

"Makin darts, eaten'....What ever this is" ~ UberKuhlMan

#10 SaucyGanzalez

SaucyGanzalez

    Member

  • Members
  • 109 posts
  • Location:Cincinnati Ohio

Posted 27 June 2010 - 11:21 PM

Shit! Sorry for the triple post, stupid computer.

Edited by SaucyGanzalez, 27 June 2010 - 11:23 PM.

  • 0
"Fuck it, ill use a hacksaw" ~ SaucyGanzalez

"Makin darts, eaten'....What ever this is" ~ UberKuhlMan

#11 Zorns Lemma

Zorns Lemma

    Sir Scrt

  • Moderators
  • 1,277 posts
  • Location:Dulles International Airport
  • State:Virginia
  • Country:United States

Posted 28 June 2010 - 12:55 AM

I really like this mod, I just have one question: doesn't the slide get in the way of the dart tooth?


Good thing he doesn't have one!
  • 0
"In short, the same knowledge that underlies the ability to produce correct judgement is also the knowledge that underlies the ability to recognize correct judgement. To lack the former is to be deficient in the latter."
Kruger and Dunning (1999)

#12 moosa

moosa

    Member

  • Members
  • 243 posts
  • Location:Bangor, ME

Posted 28 June 2010 - 03:52 AM

Okay, you've got your image URLs, and right after each of them you've got "[/img]"
What you need is to do this:
[img]-IMAGE URL HERE-[/img]

Then your images will work.
  • 0
Yes.

#13 thedom21

thedom21

    Member

  • Members
  • 462 posts
  • Location:Saint Paul MN
  • State:Minnesota
  • Country:United States

Posted 28 June 2010 - 10:40 AM

I really like this mod, I just have one question: doesn't the slide get in the way of the dart tooth?

I don't need the dart tooth because I did a Brass Breach.
  • 0
Funny Irc moments

22:32 hookerninja I would just switch to 2 full 69's
22:32 hookerninja that would diddle shit

11:44 Zorn Her butt is too tiny even for limp 6th grade penis?
11:44 Zorn ergo the dildo

#14 SaucyGanzalez

SaucyGanzalez

    Member

  • Members
  • 109 posts
  • Location:Cincinnati Ohio

Posted 28 June 2010 - 11:45 AM

I really like this mod, I just have one question: doesn't the slide get in the way of the dart tooth?

I don't need the dart tooth because I did a Brass Breach.


Oh, beautiful work then.
  • 0
"Fuck it, ill use a hacksaw" ~ SaucyGanzalez

"Makin darts, eaten'....What ever this is" ~ UberKuhlMan

#15 thedom21

thedom21

    Member

  • Members
  • 462 posts
  • Location:Saint Paul MN
  • State:Minnesota
  • Country:United States

Posted 28 June 2010 - 11:56 AM

I will be doing contracts on longshots and BBB's or almost anything else. Just PM me if you want me to.
  • 0
Funny Irc moments

22:32 hookerninja I would just switch to 2 full 69's
22:32 hookerninja that would diddle shit

11:44 Zorn Her butt is too tiny even for limp 6th grade penis?
11:44 Zorn ergo the dildo


0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users