This is what the finished gun looks like
before paint
after paint
[img]http://img14.imageshack.us/img14/4933/dsc02979y.jpg[img]
photo quality is kinda crappy now but you get the picture
Materials:
high temp hot glue gun.(low temp does not work well)
dremel
hack saw
needle nosed pliers
at least 7" of one inch pvc
Start off by taking out all the screws and removing the top cover. Now the gun is open.
oh and p.s. take a flat screw driver to pry off that green peice at the end.
[img]http://img168.imageshack.us/img168/6521/dsc01945fu0.jpg[/img]
(this is not my picture, i just found it on google image search)
Next we are going to move the the pump over
Move the pump out of the way as not to cut it. Cut it with a dremel or a hack saw and make sure to cut where it says in the picture. Set this peice aside for later.
[img]http://img40.imageshack.us/img40/1384/63314354.gif[/img][/img][img]
Now cut a peice of one inch pvc to form the new pump. It will need to about 7 inches long.
The next part can be put on either the right or left side. I put mine on the right as to provide easy disasembly and access to the internals.
Dremel the peice of plastic around the the back of the pump casing so the new pump can move over.
[img]http://img41.imageshack.us/img41/2636/15102221.jpg[/img]
Next remove the the cap at the end of the pump
[img]http://img29.imageshack.us/img29/558/58263756.jpg[/img]
It should come off very easily.
Slide the 1" pvc over the pump and hot glue it, as you see in the picture before the last.
Put the inner end cap back on and cut the end peice off of the original pump casing. Cut where it says in the picture.
[img]http://img20.imageshack.us/img20/5310/0065356916740500x500.jpg[/img]
Now we can move on to the clip.
There are two options for the next step.
1)keep reading mine which goes into less detail
2)folow the link to captian slugs clip modification here- http://nerfhaven.com/forums/index.php?showtopic=7433
Ok the next thing is kinda tricky, so the holes are at 45 degree angle to each other and cut exactly how i cut in the pictures.
[img]http://img514.imageshack.us/img514/5546/75139652.jpg[/img]
[img]http://img513.imageshack.us/img513/5488/48025909.jpg[/img]
[img]http://img170.imageshack.us/img170/1144/90970419.jpg[/img]
[img]http://img38.imageshack.us/img38/9908/49368860.jpg[/img]
Take your needle nosed pliers and twist out the air restrictors.
Ok now that we have that out of the way time to do the easiest part, take your dremel and sand down the little green knob at the end of the air blader.
[img]http://img170.imageshack.us/img170/8338/76941991.jpg[/img]
Now re-asemble the whole gun and now we are finished with all the internal stuff.
p.s. it will be tricky cause of the the way the new pumps angle.
Now for the external stuff my speciality!!
Cut the old pump casing in these places:
[img]http://img31.imageshack.us/img31/3930/51380284.jpg[/img]
I forgot to take pictures of this next part, but I'll try to explain them in as much detail as i can.
Turn over the first section where it says magstrike and sand down all the ribs so it will fit around the pvc pipe.
use a genorious amount of hot glue to attach it. hold tight for about 1 min. then atach the next side the same way. Next we will attach the bulky part at the end with more hot glue. it may take a little dremeling to get it to fit.
Now we are all done.
I will try to have a video of it firing soon but i have to fix a leek in the tubes.(unrelated to the moddifing. It was a three year old gun its bound to have leaks.)
Edited by wohnson89, 14 September 2009 - 05:43 PM.
