Jump to content


Photo

"the Blood Finder"

Nightfinder with an AT3K

40 replies to this topic

#1 Banshee

Banshee

    Member

  • Members
  • 668 posts

Posted 14 May 2009 - 09:42 PM

I was recently admiring the work of PointBlank's "Cyclops" mod and how he managed to get an Airtech 3000 tank inside a nightfinder shell. However I wasn't so pleased with the idea of removing the perfectly good internals of my nightfinder, so I came up with a way to have both guns functionally in one gun. This is a VERY similar mod however we externally mount the pump.

The first part is not pictured, but you're going to want to take your AT3K tank and strip it completely clean of all flanges and extremities.

The you're going to take the housing of your light, remove all the wires and the light, but keep the housing. cut the flange off of the bottom so it will sit flat. Attach your barrel material inside the light and glue the whole thing to the front end of the tank like so:

Posted Image

Keep in mind however that when your tank and barrel assembly are inserted your pump valve is going to need to come out the side, so plan how you glue them all together.

Then you're going to need to drill a hole in the side of the gun where your pump valve will come out of.

Posted Image

Also, you're going to want to drill out and remove all screw posts from where the light used to be so the tank can fit. Then you're going to cut out the front enough for the tank to fit through the front. Its so unfortunate that it wont fit by such a small distance.

Posted Image

Then we need to move on to the Nightfinder internals. You can do any of the basic mods you choose. I chose to attach the CPVC barrel inside the internal coupler from the plunger tube and the stock barrel like this:

Posted Image

I then put an ACE #49 spring on the plunger and put some Teflon tape underneath the o-ring for a better seal.

Posted Image

Then I filed down the barrel tip so the CPVC will fit through:

Posted Image

Now to the AT3K trigger system. For this I did a linked trigger so I can fire both shots at the same time or still have the option of cock-shoot-cock-shoot. For this I bent the tank pin in a full circle:

Posted Image

Now be VERY careful when you do this, use 2 pares of pliers, one to hold the pin and one to bend it. If you just try and bend the pin you could break the plastic on the tank and create a fatal leak.

Next we're going to drill a hole in the trigger in the rear for out new trigger wire.

Posted Image

I didn''t get a picture of it, but I used a section of wire hanger between the trigger and the firing pin and ran it underneath the original trigger.

I also drilled some holes through the trigger for some extra style points and attached the brass end of a 12 gauge Remington shot gun shell to the pump as a pump handle. Its very comfortable.

Posted Image

This photo was taken after painting it, but I've attached the pump to the left side next to the light with epoxy putty. I advise nothing less than epoxy putty. My first attempt with liquid epoxy failed to hold through a small indoor battle and hose clamps just let it slide though, so use plenty of epoxy putty.

Posted Image

Now you can put it all back together, with your AT3K internals AND your NF internals. I ran the hose underneath the front of the trigger guard, through the gap under the barrel and into the side where the tank is. I sprayed mine with a candy apple red metallic paintjob. And I give you the "Blood Finder".

Posted Image

1 Billion internetz to the person who can identify the movie on my computer in the background.

Pump side:

Posted Image

Front end:

Posted Image


Ranges are typical:

Nightifnder Average: 75'

Airtech 3000 Average: 1 Pump: 60', 2 Pumps: 80', 3 Pumps: 90'+


Questions, Comments?

Edited by Banshee, 14 May 2009 - 11:23 PM.

  • 0
Like my page on Facebook! PM me, I do commissions!

#2 alextwin007

alextwin007

    Member

  • Members
  • 96 posts

Posted 14 May 2009 - 09:47 PM

This is really nice. I like the way you kept the night finder functional as well as the 3K. Also nice place to put the pump, props. I love it when someone finds good use for the space that war the light.

Edited by alextwin007, 14 May 2009 - 09:52 PM.

  • 0
Join the revolution
Nerf Revolution

#3 NerfRogue83

NerfRogue83

    Member

  • Members
  • 646 posts

Posted 14 May 2009 - 09:49 PM

Wow, you really took things to the next level. Very nice, and exceedingly clean!---Rogue.
  • 0
IRC chat: louiec3-- he offered $500 for someone to build a bomb he could send to his ex wife
Rknight-- wow......N9---your dad is in trouble now!


#4 SonReeceSonJensen

SonReeceSonJensen

    Member

  • Members
  • 662 posts

Posted 14 May 2009 - 10:06 PM

Just beastly, the candy paint and the black barrels are very nice. I also like how the brass shell part makes it look a titch Iron Man-y.
  • 0
The Difference:
-Guns shoot bullets that kill people
-Blasters shoot darts that tag people

I do not play with guns.

#5 clubace

clubace

    Member

  • Members
  • 12 posts

Posted 14 May 2009 - 10:10 PM

I like it, its very clean and the paint job is pretty sweet. The shot gun shell for the pump is pretty excellent as well, is it hard to pump the gun with that though? It just seems like a small thing to hold on to, but I do have rather large hands.
  • 0

#6 Banshee

Banshee

    Member

  • Members
  • 668 posts

Posted 14 May 2009 - 10:18 PM

I like it, its very clean and the paint job is pretty sweet. The shot gun shell for the pump is pretty excellent as well, is it hard to pump the gun with that though? It just seems like a small thing to hold on to, but I do have rather large hands.

No, not at all. Its about the size of an AT2K pump handle and I usually only do one pump anyways. And I have pretty big hands too.
  • 0
Like my page on Facebook! PM me, I do commissions!

#7 JATDO

JATDO

    Member

  • Members
  • 350 posts

Posted 14 May 2009 - 10:38 PM

When I read the post title I was ready for a "cyclops" carbon copy, but this is amazing.
I love it. The pump handle and placement is engenious. (sp?) As well as the trigger linking. You said in the write up you wanted the option of both shots at once or semi-auto. How could that be semi?

Mega props.
  • 0
QUOTE
I remember when some girl in my English 101 class in college tried to cite The Onion as a source for her paper. The teacher lol'd.
QUOTE
The only time I got hit was when my spotter got hit and the enemy team realized there was a marksman in the bushes

#8 Banshee

Banshee

    Member

  • Members
  • 668 posts

Posted 14 May 2009 - 10:42 PM

When I read the post title I was ready for a "cyclops" carbon copy, but this is amazing.
I love it. The pump handle and placement is engenious. (sp?) As well as the trigger linking. You said in the write up you wanted the option of both shots at once or semi-auto. How could that be semi?

Mega props.


Well, I don't have it rigged right now to be semi but it is possible. Right now, one trigger pull fires them both at the exact same time, but if I where to trim the trigger a bit and tighten up the linkage, i could get the AT3K to fire on half a pull and the NF to fire on the whole pull thus being semi auto, but I liked it better this way. Right now, I pump it once, shoot a dart, then I cock it and shoot another.
  • 0
Like my page on Facebook! PM me, I do commissions!

#9 rokor

rokor

    Member

  • Members
  • 792 posts

Posted 15 May 2009 - 04:42 AM

This reminds me of NortherofHeavens integration... but I like this one more only because it looks "ballin" haha.

P.S. Is the movie Transformers?
  • 0
"Sorry rokor...my cousin is gay too...it's okay...we're tolerant"
Talio in Shoutbox.

#10 Banshee

Banshee

    Member

  • Members
  • 668 posts

Posted 15 May 2009 - 08:26 AM

This reminds me of NortherofHeavens integration... but I like this one more only because it looks "ballin" haha.

P.S. Is the movie Transformers?

Nope, not Transformers, good guess, try again!
  • 0
Like my page on Facebook! PM me, I do commissions!

#11 diamondbacknf1626

diamondbacknf1626

    Member

  • Members
  • 835 posts

Posted 15 May 2009 - 08:36 AM

This reminds me of NortherofHeavens integration... but I like this one more only because it looks "ballin" haha.

P.S. Is the movie Transformers?

Nope, not Transformers, good guess, try again!



I'm not even trying on the movie; that picture's just way too vague.

As to the gun though, nice work. I do like that you kept the nitefinder functionality wise, but the only reason I would still choose the cyclops over this is cleanliness. Yes, you did it cleanly, but it still has the pump stuck to the side. Something tells me that this is far less awkward to pump though than something like the Cyclops.
  • 0
QUOTE(TxNerfer @ Nov 13 2010, 12:42 PM) View Post

Hey...I got a crazy idea: how about you stop all that sigging stuff? It's not even my thread and it annoys me.

#12 SweetVengence

SweetVengence

    Member

  • Members
  • 6 posts

Posted 15 May 2009 - 09:41 AM

Very clean integration. The paint looks very nice. What paint did you use?

And is the movie I Am Legend?
  • 0

#13 PointBlank

PointBlank

    Member

  • Members
  • 528 posts

Posted 15 May 2009 - 11:32 AM

It looks really nice. I like the paint job and the pump placement looks handy.
  • 0
You can agree with me.... or you can be wrong.

My Latest Mods
The Cyclops
Pointblank Titan

#14 JATDO

JATDO

    Member

  • Members
  • 350 posts

Posted 15 May 2009 - 01:38 PM

Have you tried shotgun loading the at3k?
Shotgun then nitefinder. :ph34r:
  • 0
QUOTE
I remember when some girl in my English 101 class in college tried to cite The Onion as a source for her paper. The teacher lol'd.
QUOTE
The only time I got hit was when my spotter got hit and the enemy team realized there was a marksman in the bushes

#15 DrSpaceman

DrSpaceman

    Member

  • Members
  • 97 posts

Posted 15 May 2009 - 04:00 PM

Great idea and gun.

I think the movie is X-Men:Last Stand (The part where they fight the sentinel).
  • 0
"I'm being very open with you miss... I shouldn't have taken those blue things."
-Dr. Spaceman on 30 Rock

If you see me in the trading forum, I am most likely posting for friends. They are very into trading/buying/selling guns. Me, not so much.

#16 Applefury

Applefury

    Member

  • Members
  • 233 posts

Posted 15 May 2009 - 04:09 PM

This is a really good clean modification, nice job! Seems like a great sidearm.

My guess for the movie is Slumdog Millionaire.
  • 0
QUOTE(Gamefreak @ Sep 29 2008, 07:03 PM) View Post

Since you're too young to get a hotel, you should look around, maybe check some aim chatrooms.
Theres alot of really friendly, nice people out there, that'd be more than willing to accomodate a young boy.

#17 Banshee

Banshee

    Member

  • Members
  • 668 posts

Posted 15 May 2009 - 04:51 PM

Thank you for all your compliments! And no, sorry the movie is not I am Legend, X-men, or Slumdog. None of you will guess what movie it is. You all know the movie, but I just happened to pause it at a point that looks like it could be anything. But anyways, this thread is about my gun.

The paint I used is a Duplicolor automotive paint. I love their paints because they have pan spray nozzles, really comfortable, the paint doesn't chip, smudge, or crack, its a beautiful color, it goes on VERY even, very fine so you can get it in any nook and cranny, and best of all, it dries to the touch in like 10 minutes. I painted the gun and put some 10 minute dry clear coat on it LITERALLY half an hour before I posted pictures.
  • 0
Like my page on Facebook! PM me, I do commissions!

#18 SchizophrenicMC

SchizophrenicMC

    Member

  • Members
  • 390 posts

Posted 15 May 2009 - 04:59 PM

I don't see as much love for the 3k as the 2k. Insanely clean integration, great paintjob, functional.

You get many points for this.




The movie is Jurassic Park.
  • 0
QUOTE(NerfUK @ May 8 2009, 11:54 AM) View Post

(I forgot to take a picture of my own poppers)

QUOTE(analogkid @ May 20 2009, 10:04 PM) View Post

Every size rod you could ever want.

#19 VelveetaAvenger

VelveetaAvenger

    Member

  • Members
  • 630 posts

Posted 15 May 2009 - 06:43 PM

Nice job on the mod, but I'm just here to guess at the movie, could it possibly be Mad Max?
  • 0
"I never saw Beastmaster, I just wanted to be cool..."

#20 BritNerfMogul

BritNerfMogul

    Member

  • Members
  • 560 posts

Posted 15 May 2009 - 06:53 PM

Love it. Great work with the blaster and I really like the paint job.

Transformers.
  • 0

#21 Banshee

Banshee

    Member

  • Members
  • 668 posts

Posted 15 May 2009 - 07:24 PM

Love it. Great work with the blaster and I really like the paint job.

Transformers.

Coming from you, that means a lot. Your paint jobs are absolutely SICK. And all of you are still wrong about the movie.
  • 0
Like my page on Facebook! PM me, I do commissions!

#22 BritNerfMogul

BritNerfMogul

    Member

  • Members
  • 560 posts

Posted 15 May 2009 - 07:33 PM

Love it. Great work with the blaster and I really like the paint job.

Transformers.

Coming from you, that means a lot. Your paint jobs are absolutely SICK. And all of you are still wrong about the movie.


Thanks. I just love the candy paint.

Shit. Thought I'd got it.
  • 0

#23 SchizophrenicMC

SchizophrenicMC

    Member

  • Members
  • 390 posts

Posted 15 May 2009 - 07:44 PM

I'm just gonna throw this out there: Back to the Future?
  • 0
QUOTE(NerfUK @ May 8 2009, 11:54 AM) View Post

(I forgot to take a picture of my own poppers)

QUOTE(analogkid @ May 20 2009, 10:04 PM) View Post

Every size rod you could ever want.

#24 BritNerfMogul

BritNerfMogul

    Member

  • Members
  • 560 posts

Posted 15 May 2009 - 07:47 PM

Clue time me thinks.
Everyone agree?
  • 0

#25 Banshee

Banshee

    Member

  • Members
  • 668 posts

Posted 15 May 2009 - 07:50 PM

Clue time me thinks.
Everyone agree?

Okay, its a war movie.
  • 0
Like my page on Facebook! PM me, I do commissions!


2 user(s) are reading this topic

0 members, 2 guests, 0 anonymous users