Ok now for my other question. I have a Buzz Bee RFR and I heard it was a good idea to reinforce the catch, can someone tell me how to do this?
Thanks everyone!
Edited by Roschili, 09 May 2009 - 11:10 AM.
Posted 06 May 2009 - 05:30 PM
Edited by Roschili, 09 May 2009 - 11:10 AM.
Posted 06 May 2009 - 05:33 PM
Posted 06 May 2009 - 05:36 PM
Cut off the ring between the slide-out handle and the main gun shell.
Posted 06 May 2009 - 05:36 PM
Posted 06 May 2009 - 05:40 PM
Actually, I found that pulling it at a 30 degree angle away from the oval looking thing gets it right out.
Posted 06 May 2009 - 05:48 PM
Posted 06 May 2009 - 06:10 PM
Posted 06 May 2009 - 06:17 PM
Posted 06 May 2009 - 06:29 PM
Edited by Roschili, 06 May 2009 - 08:41 PM.
Posted 09 May 2009 - 11:10 AM
Posted 09 May 2009 - 11:21 AM
Posted 09 May 2009 - 11:41 AM
Cut off the gray part with a hacksaw.
Posted 09 May 2009 - 11:50 AM
Edited by DrSpaceman, 09 May 2009 - 12:59 PM.
Posted 09 May 2009 - 12:00 PM
Dip the handle in boiling water for a few minutes. This may loosen up the glue holding together so that you can pry it off without otherwise damaging it.
Posted 09 May 2009 - 12:01 PM
QUOTE(Daniel Beaver @ May 6 2009, 04:17 PM) *
Dip the handle in boiling water for a few minutes. This may loosen up the glue holding together so that you can pry it off without otherwise damaging it.
Do this. It works.
Edited by Roschili, 09 May 2009 - 12:03 PM.
Posted 09 May 2009 - 12:03 PM
Edited by coltsboy29, 09 May 2009 - 12:04 PM.
Posted 09 May 2009 - 12:10 PM
Not on an eliminator, but it has worked for other guns that have pieces glued together. I would give it 15 seconds, then try to pull it off. If that doesn't work, give it 30 seconds, and so on. You want to be a bit careful when using this method, as it can warp the plastic.Have you done it before?
I will probably try it, how long should I keep it in water?
Posted 09 May 2009 - 12:16 PM
Dip the handle in boiling water for a few minutes. This may loosen up the glue holding together so that you can pry it off without otherwise damaging it.
Do this. It works.
Posted 09 May 2009 - 12:31 PM
Posted 09 May 2009 - 12:35 PM
Edited by Roschili, 09 May 2009 - 12:40 PM.
Posted 09 May 2009 - 01:03 PM
Posted 09 May 2009 - 02:06 PM
You can try using a blowdryer to heat up the pieces and loosen the bond of the glue.
As for your second question, remove the original catch spring and replace it with a spring from a pen that is a bit longer. Then hot glue the spring on so it is harder to compress.
Edited by Roschili, 09 May 2009 - 09:12 PM.
Posted 10 May 2009 - 05:32 AM
Put the hot glue inside the spring, and while it is still warm put it back on the peg where it originally was.You can try using a blowdryer to heat up the pieces and loosen the bond of the glue.
As for your second question, remove the original catch spring and replace it with a spring from a pen that is a bit longer. Then hot glue the spring on so it is harder to compress.
I tried using a blow dryer on the hottest setting and it did not help so next I will try boiling water when I get the chance. Edit, I also tried running a dremel along the seams where it was glued but I did not go deep and it didn't help any.
Thanks, where would I put the hot glue at? Just glue the end of it to the wall it compresses against?
Posted 10 May 2009 - 08:42 AM
Put the hot glue inside the spring, and while it is still warm put it back on the peg where it originally was.
Posted 10 May 2009 - 10:02 AM
0 members, 1 guests, 0 anonymous users