Recon Spring Addition With Removable Stock
#1
Posted 15 January 2009 - 04:25 PM
In this mod, you’ll be doing a well known Recon mod: housing an extra spring. The difference between this mod and the other ones is that the stock will still be removable. It’s a simple mod that will never even allow your internals (besides the plunger tube) to see the light of day, and the materials used to make it are found in almost every house.
Inspiration for this came when I was gluing something down in school, and thought about Nerf Guns, and Crayola barrels came to mind. I though, “Hmmm. What would be a good mod for my new Recon?” I looked at my glue stick and scribbled down a plan. I got home that day, did it in 10-15 minutes, and loved my Recon.
Ok, for this mod you’ll need:
A Phillips head screwdriver
A FAT Elmer’s glue stick
A hacksaw
A miter box (optional for straight cuts)
Electrical tape or maybe duct tape
A smaller spring of your choice (can’t use one much longer than 2.8 – 3 inches)
A quarter
A second/third generation Nerf Recon (? don’t if I have second or third. Well. Just one with the full length black cover on the plunger tube, with just a small slit on the end that’ll appear orange if the gun is primed.)
1. First, before you even do this mod, I recommend doing the following mods, as
they’re all great and will add to the overall performance of your Recon.
http://nerfhaven.com...showtopic=10436
http://nerfhaven.com...showtopic=10444
http://nerfhaven.com...showtopic=10498
I recommend also stretching your Recon spring.
2. Ok, so, you’re done all those mods. First things first, unscrew your black plunger cover off of your gun. Put it in your miter box. Saw off the VERY end of it (the end facing the stock with the small n-shaped slit in it.) Don’t saw off more than 2/16 of an inch.
3. Next, grab your Elmer’s glue stick. Take off the cap and twist the bottom counter-clockwise until you can pull out the actual stick of glue.
4. Take your glue stick and saw off at the red lines:
5. Punch out the corkscrew, however you can. I used a hammer and a screwdriver:
6. Next, take your two pieces so far (sawed cover and glue stick) and sand them as even as possible. Using your tape, wrap these two together tightly with several layers. And I mean a lot of layers, as in around 9. I used an electrical-type tape, but had some coarseness to it. Watch out, if you don’t wrap it enough, it can actually blow the glue stick piece right off of the cover.
7. Take your quarter and place it on the end of the glue stick-piece. Wrap that with tape to close it off. You should now have a thick, longer plunger tube cover. Make sure your stock is off, and pop a spring in your new cover. Screw it back onto your gun
8. You’re almost done. Using this diagram, unscrew these screws on your Recon’s stock:
Take off that piece.
9. Congrats! You’re done. Your stock is now removable, without getting rid of the added spring functionality! I did this mod over a normal spring add on because of its cleanliness, the no-stock functionality (as I thought that with no stock, it’s cool to have a pistol-sized Longshot…) and it basically looking the same.
[c]~Random pictures~
Cover in comparison to old cover
Finished gun with stock
Any suggestions to editing this mod is appreciated! Enjoy!
... to be able to get a better burst or sustained fire, rather than blowing the whole load at once.
#2
Posted 15 January 2009 - 04:33 PM
#3
Posted 15 January 2009 - 04:46 PM
... to be able to get a better burst or sustained fire, rather than blowing the whole load at once.
#4
Posted 15 January 2009 - 05:32 PM
#5
Posted 15 January 2009 - 05:59 PM
What did you reinforce your own stock with foam? If you did than of course it will bend. Instead use what I use 22gauge steel. It will never bend again.that is not a good idea...That would make your stock EXTREMELY flimsy. And with 2 springs in that gun, I'm sure after repeated use your stock would break. Mine has a reinforced and weighted stock, and even then the stock still bends a tad when I prime the gun. I would suggest using some foam, or even just tape to strengthen it a bit.
#6
Posted 15 January 2009 - 06:00 PM
... to be able to get a better burst or sustained fire, rather than blowing the whole load at once.
#7
Posted 15 January 2009 - 07:16 PM
Hell, when I am aiming the gun it usually warps a bit.
And this might work better with First Gen Recons since it already has a hole in the stock.
#8
Posted 16 January 2009 - 04:41 PM
... to be able to get a better burst or sustained fire, rather than blowing the whole load at once.
#9
Posted 16 January 2009 - 10:39 PM
That's exactly what I was trying to say, thanks for clearing that up for everyone that didin't understandThe stock is two very thin plastic rods. When you have it shouldered, the force created when you cock the gun warps the stock. With the added spring and the removed central support, the stock might become too flimsy and break when you cock the gun.
Hell, when I am aiming the gun it usually warps a bit.
And this might work better with First Gen Recons since it already has a hole in the stock.
What did you reinforce your own stock with foam? If you did than of course it will bend.
Not expandible foam. You put it on the stock, it expands to fill the space between the two thin plastic bars, it then hardens, and makes the stock much sturdier. I suggest it to anyone who has a flimsy stock.
#10
Posted 17 January 2009 - 03:41 AM
#11
Posted 18 January 2009 - 05:41 PM
... to be able to get a better burst or sustained fire, rather than blowing the whole load at once.
1 user(s) are reading this topic
0 members, 1 guests, 0 anonymous users