Jump to content


Photo

Recon Mods


11 replies to this topic

#1 Raven2049

Raven2049

    Member

  • Members
  • 16 posts

Posted 27 December 2008 - 10:18 PM

yes I know (or at least I have read) that recons are kinda extremely erotic here, but I kinda like the look of it, but the technique needed to cock it sucks big time (hand over the top to pull it back) and with the front barrel extension on it, the rail on the bottom of the extension is basically begging to have a shotgun grip ala capt. slug LS grip done to it.

so without further adieu here's my first mod. Ill do better pics later when I get a better camera (using my cell phone camera at the moment)

Parts used:
LS front gun:
grip
screws
1 piece of polycarbonate approx 6" x 10"

Needed:
Exacto knife
something to cut the polycarbonate
marker
5/32 drill bit
hot glue
epoxy

Posted Image

I just got done tearing apart the front gun for my LS and had the parts strewn about my desk, and my brand new Recon lying on here also, and while I was browsing the forums figuring out what to do to it i realized nobody likes them. That's understandable, I only bought it for the looks, and the attachments for my Vulcan.

but I saw the LS front gun grip, and thought... Hmmm that would look great on the recon as a pump. and so, 2 hrs later, some hot glue, some epoxy a few pieces of polycarbonate and some screws here's the result:

Posted Image

I had to put 2 pieces of the poly as spacers in the grip to accommodate the width of the barrel, so I had to use some long screws, luckily the screws from the back of the ls front gun were about an inch in length and they worked excellent, I had to drill 2 holes in the poly spacers in order to get the grip to fit properly but it worked well. those spacers also became an excellent slide base (or top depending on your perspective) for the grip against the bottom rail of the barrel.

Posted Image

Posted Image

I shaved down some of the raised pieces of the grip in order to accommodate the poly pieces that connect to the slide (along with the stud that slides through the front gun body). and epoxied a 10" by 1" piece of poly to that area I just prepared and reinforced it with some hot-glue.

Posted Image

I then cocked the Recon, and put the completed fore grip against the barrel, exactly where it was going to go and all the way back so its in the fully primed position. During this time its easiest to have the sides of the slider off and working with them individually. I then drew an outline around the poly pieces and taped them to the slide. then using a very small drill bit, I drilled 3 holes per side, and using the screws from the body of the LS front gun I fastened the slide, and the grip. make sure that you use some of the shorter screws so that the screws don't scrape against the side of the body of the gun. On the side that has all the warnings I had to shave the letters off with the knife in order for the slide to fit nicely, also on both sides there is a fake "screw" on the slide that I had to cut off in order for the poly pieces to fit properly.

Posted Image

After that its a small task of putting everything back together and testing it out.


this mod was made to be removable, I was originally going to epoxy the poly pieces straight to the slide, then I decided against it because I figure I would want to paint it, or work on it later (possibly put the stock reinforcement mod/spring mod I saw earlier in)

anyways there ya go! my first mod submitted for everyone.

ideas/comments/suggestions?

Edited by Raven2049, 27 December 2008 - 10:41 PM.

  • 0

#2 s3an967

s3an967

    Member

  • Members
  • 83 posts

Posted 27 December 2008 - 10:20 PM

Very nice. Very clean. I was tempted to do this if my LS front gun fore grip wasn't used.
  • 0
Watch this- I can tip-toe while you take a piss.

#3 Heedfulkiller

Heedfulkiller

    Member

  • Members
  • 36 posts

Posted 27 December 2008 - 10:26 PM

this kind of defeats the point of customizing the gun. But still a good mod. good job!
  • 0
"THEY RUN AROUND, PLAY AROUND, AND EAT PEOPLE!"
my little brother explaining a small dinosaur

"I BUILT A TACO, A METAL TACO!"
another quote from my little brother

#4 Soothsayer

Soothsayer

    Member

  • Members
  • 663 posts

Posted 27 December 2008 - 10:28 PM

this kind of defeats the point of customizing the gun. But still a good mod. good job!

But it does take a piece of shit and turn it into a pump action piece of shit.

Another great tutorial on polishing a turd.

In all seriousness, good job. Bigger pictures would be good.
  • 0

yeah I'm that guy who made that cool thing with the cool paint.


#5 Raven2049

Raven2049

    Member

  • Members
  • 16 posts

Posted 27 December 2008 - 10:29 PM

Na if your talking about adding the different things to the rails, you still have the rail on the top of the barrel (which in my one picture i have the tac-light on it, and then you also have the rail on the slide itself. and yes you can still use that rail, in fact I'm thinking about putting the LS scope on it, only thing ill have to watch out for is when I cock it the scope doesn't hit me in the face

EDIT: I fixed the first two images being so small when you clicked on them.

Edited by Raven2049, 27 December 2008 - 10:42 PM.

  • 0

#6 hummer

hummer

    Member

  • Members
  • 217 posts

Posted 27 December 2008 - 11:02 PM

Well done! (Although when you said shotgun, i thought you were going to add a more...shotgun-looking gun to the bottom, well thought out none the less)
Are you going to add the spring extensions now? (because you pretty much need the stock to pump it anyway)
I was thinking of saving up for a long shot too, thanks for making my decision that much easier!

Edited by hummer, 27 December 2008 - 11:04 PM.

  • 0
Into the fires of battle!
Onto the anvil of war!
QUOTE(BustaNinja @ Nov 23 2010, 04:09 PM) View Post

He parkours over flat land while yelling tactical orders at no one. Demon Lord is the most legit ballsy nerfer of all time.

#7 boisie

boisie

    Member

  • Members
  • 303 posts

Posted 27 December 2008 - 11:45 PM

Go to hasbro and get the recall arm bar cover, and use that instead of the stump you have. It'll give you room for a spring extension.
  • 0
QUOTE(One Man Clan) View Post
You understand what you just did posting a picture of 4 girls on a message board chock full of nerdy virgins, right?
QUOTE(Foamfoot) View Post
Maybe if we download Ubuntu Christian edition, God will help us install it.

#8 Lion

Lion

    Member

  • Members
  • 244 posts

Posted 28 December 2008 - 12:31 AM

Another great tutorial on polishing a turd.




Off topic: MythBusters did that, and proved that it can be done and to a high gloss, but it is still a turd



Nice mod though, looks very usefull.
  • 0

#9 Renegademilitia15

Renegademilitia15

    Member

  • Members
  • 516 posts

Posted 28 December 2008 - 01:27 AM

Wow, really nice. I just recently got a recon and have been modding it this week, and since I have a LS front gun sitting in my closet, I am definitely going to do this mod.

I would clean up your entire post though, there is a lot of capitalization errors in there.

All in all, wonderful first mod.

Edited by Renegademilitia15, 28 December 2008 - 01:28 AM.

  • 0
Singled RFS
FA_24's response to Ice's back pain thread:
QUOTE

I used to have that problem until I got circumcised. 15 pounds later I was able to stand up straight.

#10 Raven2049

Raven2049

    Member

  • Members
  • 16 posts

Posted 01 January 2009 - 10:42 AM

Yes I know I'm necroing my own topic, but I have a question: where can I get the replacement stock that Boisie was talking about? I checked Hasbro.com and couldn't find it.


---------------------------------------------------------------------


Also after playing around with my mod for a while I discovered that the front grip gets kind of loose after a few days, Id recommend hot-gluing it together or epoxying it.

Also the grip gets stuck on the orange decoration on the barrel when you cock it, Id recommend cutting it off of the barrel, or if you like the look of it, trim the grip all the way flush from where the poly strips that connect to the slider ends.

Other than that I haven't noticed any other problems
  • 0

#11 Draconis

Draconis

    I am not Lord Draconical

  • Members
  • 2,712 posts

Posted 01 January 2009 - 12:55 PM

Yes I know I'm necroing my own topic, but I have a question: where can I get the replacement stock that Boisie was talking about? I checked Hasbro.com and couldn't find it.


It's under product safety. Here is a link: http://www.hasbro.co...S-6-Blaster.cfm

It's just a plunger tube cover, though. Not a whole stock.

Also, it's not really a necro until the topic is dead for over a month. But as long as you add something worthwhile, it's usually okay to post in YOUR OWN topic even after that time.

Edited by Draconis, 01 January 2009 - 12:58 PM.

  • 0
[15:51] <+Noodle> titties
[15:51] <+Rhadamanthys> titties
[15:51] <+jakejagan> titties
[15:51] <+Lucian> boobs
[15:51] <+Gears> titties
[15:51] <@Draconis> Titties.
[15:52] <+Noodle> why is this so hard?

#12 Raven2049

Raven2049

    Member

  • Members
  • 16 posts

Posted 01 January 2009 - 02:19 PM

ah, i have the latest version of the recon, it already has that on it.

Edited by Raven2049, 01 January 2009 - 10:09 PM.

  • 0


1 user(s) are reading this topic

0 members, 1 guests, 0 anonymous users