Jump to content


Photo

Petg Breech

Write-up

13 replies to this topic

#1 OfAllTheNerf

OfAllTheNerf

    Member

  • Members
  • 714 posts

Posted 07 September 2008 - 04:36 PM

What you will need:

Posted Image

10" of 1/2" PVC
1 1/2" of 1/2" brass
1 foot of PETG (I'm using OMC Thick-walled)
e-tape
Plumber's Goop
Small ring of CPVC
Dremel with cutting wheels and sanding bits, or other cutting/sanding devices

A air duster is also helpful to clear off all of the PVC dust.

Take your PVC and round out one end (this is the one that will be going into the coupler)

Posted Image

Now make a mark 1" from that end, and then another 3" after that.

Posted Image

Now mark out a dart slot.

Posted Image

Cut it out.

Posted Image

Now take your 1 1/2" of 1/2" brass and wrap e-tape around one end until it makes a good seal when slid into the PETG. Make it snug so it won't blow off when shot, but not so tight it is hard to remove.

Posted Image

Then wrap e-tape around the other end so it fits snugly in the PVC.

Posted Image

Glue it in with either Goop or superglue.

Now take the PETG and wrap tape (I chose masking tape) around it in several places so it doesn't jiggle around in the PVC too much.

Posted Image

Slide the barrel back in and mark the place where it meets the back part of the dart slot.

Posted Image

Take your CPVC and cut about half off.

Posted Image

Goop it on at the mark.

Posted Image

Now you're done! Let the Goop dry, and you should have a nice PETG breech.

Posted Image

If I ever get darts that fit in PETG well for air guns and springers, I would completely switch to these. As it is my darts fit weird, so I'll still be sticking to my Brass breech's for springers, and PETG ones for air guns (one of each for my crossbow (at2k integrated)).

I'll also be selling these if anyone would like to buy them. $11 shipped for one or $8 each with $3 for however many you buy. If you're intersted please post in my Sales thread (sig) or in my Breech sales thread. Let me know what you guys think of the prices also.

Questions? Comments?

-OfAll'
  • 0
[color=#FF6600][Finesse]-[BitchX]

#2 Ubermensch

Ubermensch

    Member

  • Members
  • 1,054 posts
  • Location:Cross River, New York 10518

Posted 07 September 2008 - 06:36 PM

Hey, I have that exact dremel! Did the blade/cutting bit come with yours? I think I might be missing it in my set.
  • 0
"In order to make an apple pie from scratch, you must first create the universe."-Carl Sagan
Nerf Rocket Air Launcher

#3 Z4

Z4

    Member

  • Members
  • 94 posts

Posted 07 September 2008 - 07:03 PM

Thanks, this is really cool. I too have that Dremel, or I did til it mysteriously disappeared...
  • 0
Z4 of the NIC
"We are here to have fun with the toys we love in a civilized and friendly manner."- Talio

#4 Split

Split

    Member

  • Members
  • 1,771 posts
  • Location:Hammonton
  • State:New Jersey
  • Country:United States

Posted 07 September 2008 - 07:09 PM

ZoMg! They made two edit: Three! of the same Dremel!? And I'm pretty sure that that's a worn down reinforced cutting disk. I personally use a cordless Dremel with a second battery. A lot more control, and the grip on it is comfortable and versatile.

Seriously, OfAll, try 17/32". It fits airtight in Petg with no e-tape or anything.

Edited by Splitlip, 07 September 2008 - 07:09 PM.

  • 0
Teehee.

#5 Icespartan 1114

Icespartan 1114

    Do NOT buy/sell with me

  • DO NOT TRADE
  • 934 posts
  • Location:Philly, PA 19087

Posted 07 September 2008 - 09:21 PM

Sweet i like this very much. Will you be selling these like you do with your brass breechs?
  • 0
QUOTE(Zaxbys @ Mar 2 2009, 02:08 PM) View Post
I won't be there til about 1-2...

Church... gotta soak up that Jesus!


NERFSTRONG #51

#6 Silencer

Silencer

    Member

  • Members
  • 443 posts
  • Location:Boulder
  • State:Colorado
  • Country:United States

Posted 07 September 2008 - 09:24 PM

Sweet i like this very much. Will you be selling these like you do with your brass breechs?


Look at the end of his post.
  • 0
TMC

#7 nerfnut23

nerfnut23

    Member

  • Members
  • 239 posts
  • Location:SoCal

Posted 07 September 2008 - 11:00 PM

I use a 750 RPM drill press with a 1/8" milling bit. A pain in the ass, but it gets the job done.
  • 0
American society: A legitimate clusterfuck since 1965.

#8 Daecu

Daecu

    Member

  • Members
  • 63 posts

Posted 08 September 2008 - 04:42 PM

I've mentioned before in other posts that I'm not too familiar or skilled in the area of breech design, but would this run the risk of being pushed open by the force of the release? Most breeches I see have a twist added in as a lock to prevent this...
  • 0

#9 Aimless

Aimless

    Member

  • Members
  • 169 posts

Posted 08 September 2008 - 06:27 PM

If the barrel is snug on the brass stub then it should be fine, so unless you have a really fat dart and a lot of power behind it, your barrel taking off on it's own is improbable. You can still incorporate a twist lock mechanism if you want.

Edited by Aimless, 08 September 2008 - 06:28 PM.

  • 0
It makes the world go round.

#10 Magic

Magic

    Formerly NerfOnFier

  • DO NOT TRADE
  • 540 posts
  • Location:Commack, New York

Posted 08 September 2008 - 06:30 PM

I actually made a similar breech like this earlier today, but mine only consists of E-tape, PETG, PVC, and Glue. I used no brass. =/
  • 0

#11 Shrub

Shrub

    Member

  • Banned
  • 862 posts
  • Location:Louisville,KY

Posted 10 September 2008 - 03:26 PM

Yeah I thought of making one without brass but I don't have dremel and I've heard 1/2 brass doesn't fit many peoples darts. Also would a breech be cheaper without the brass?
Favorite Quotes:
Sorry to hear that man, it's like that one famous bumper sticker, "Shit Happens"
QUOTE
it still seems that your balls drop very rapidly

#12 Galaxy613

Galaxy613

    Member

  • Members
  • 999 posts
  • Location:USA, Woodbridge, VA

Posted 10 September 2008 - 05:25 PM

IIRC brass is measured by OD unlike PVC ID. 1/2 brass thus has an OD of 1/2 which means it has a ID of about 7/16 or something like that.
  • 0
[Former Caretaker of the Guru Mk2]

#13 jwasko

jwasko

    PowerBeard

  • Moderators
  • 1,021 posts
  • Location:Pittsburgh, PA
  • State:Pennsylvania
  • Country:United States

Posted 10 September 2008 - 06:05 PM

IIRC brass is measured by OD unlike PVC ID. 1/2 brass thus has an OD of 1/2 which means it has a ID of about 7/16 or something like that.

That is correct, if my measurements are correct; My 17/32" brass has an inner diameter of 1/2" and an outer diameter of 17/32".
  • 0

-Jwasko, STILL Sole Surviving member of Steel City Nerf and Sober Sister of the Sex Dwarves
We NERF ON all day, and FUCK OFF all night


#14 needak

needak

    Member

  • Members
  • 45 posts
  • Location:Albuquerque, New Mexico

Posted 10 September 2008 - 06:48 PM

where do you get petg?
  • 0
Why the fuck would you put a bullet in someones head when you can just pump the bastard full of stefans until he's got so many welts and goose-eggs he looks like blueberry with pimples?


0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users