11 replies to this topic

[NerfCrazy]

These pictures were taken with the view finder and not the screen because that is broken. So I hope you don't mind the target being at the bottom of the pic. This is also my 7mp camera and all future writeups will be made with this camera.

Really easy to mod this gun. I feel it was easier to mod than a nf.
Supplies
hot glue
a cutting device such as a ratcheting pipe cutter
etape
cpvc and coupler
pencil or something

Here are the internals.


Now take out the barrel setup and put the yellow piece into the coupler and mark where the yellow tube goes into the coupler halfway and cut that off. Then wrap it in etape so the coupler fits on snug.


Now trim off excess etape and hot glue the coupler on. Also rough up the area where you are hot gluing.


I wrapped some etape around the area where I glued for some extra strength.

Now you will need to trim the case to fit the coupler.


Now hot glue it in and you are done.


I use a barrel about 7" and it gets at least 50'.

Edited by NerfCrazy, 25 August 2008 - 03:22 PM.

[Bomberman]

Well, it was an easy to read write-up. But what gun is this? Is it the Sharpshooter1, (I think that's what it is) or the Secret Shot one?

[Thomas]

I'm going to guess Sharpshooter, because it definitely is not the Secret Shot.

[NerfCrazy]

Yeah, the sharp shooter 1.

[Icespartan 1114]

Nice mod might try this to the sharpshooter 1 i might be getting of ebay. Ranges would be helpful. And one last thing the sharpshooter 1 shot megas, correct?

[CaptainSlug]

Nice mod might try this to the sharpshooter 1 i might be getting of ebay. Ranges would be helpful. And one last thing the sharpshooter 1 shot megas, correct?

Yes. It was released in 1992.
http://projectnerf.c...le=Sharpshooter

[Icespartan 1114]

Nice mod might try this to the sharpshooter 1 i might be getting of ebay. Ranges would be helpful. And one last thing the sharpshooter 1 shot megas, correct?

Yes. It was released in 1992.
http://projectnerf.c...le=Sharpshooter

Thanks slug

[NerfCrazy]

I would get the gun if I didn't have it because it is easy to mod and gets good ranges. FA got 70ish feet with brass.

[Dayko]

Nice mod but I have couple suggestions.

1 ) You should use a shorter barrel, like around four inches.
2 ) You should use a stronger glue for the coupler. Plumbers Goop, Epoxy, Epoxy Putty. The glue seal around the coupler will not last to long.

Other then those two things you did a good job.

[aamiller321]

Who started that project nerf wiki?

[CaptainSlug]

Who started that project nerf wiki?

CrankyMonky got the ball rolling but the Blaster List has been my pet project since November of last year. Badger kindly provided all of the blaster images.
The project Nerf Wiki is simply a backup copy of the NerfHQ wiki.

Edited by CaptainSlug, 25 August 2008 - 07:48 PM.

[NerfCrazy]

Nice mod but I have couple suggestions.

1 ) You should use a shorter barrel, like around four inches.
2 ) You should use a stronger glue for the coupler. Plumbers Goop, Epoxy, Epoxy Putty. The glue seal around the coupler will not last to long.

Other then those two things you did a good job.

1 Yes a shorter barrel would be good. I think my barrel is around 5.5-6.5".
2 I know but I couldn't find my good glues.