I have a Nerf Longshot and the breach has a tendency to tear up the ends of the darts, especially the 'rear'. This causes frequent jams and is going to cost me for the replacement ammo. Is there a modification out there to remedy this?
Any help given would be helpful, thanks.
9 replies to this topic
#2
Aimless
-
- Members
- 169 posts
Member
Posted 20 August 2008 - 01:03 AM
Don't slam the breech closed, try closing the breech slower, it should help.
It makes the world go round.
#3
keef
-
- Members
- 1,390 posts
Member
Posted 20 August 2008 - 02:44 AM
Stock breach or brassed? If stock, cut down you darts.
Timothy M-Lick <3
#4
for those about to nerf
-
- Members
- 2 posts
Member
Posted 20 August 2008 - 02:46 PM
Stock breach or brassed? If stock, cut down you darts.
angel breech
#6
Jabulus
-
- Members
- 62 posts
Member
Posted 21 August 2008 - 05:10 PM
He looked at the darts after he shot them. My recon does the same thing, but it even has a stock barrel. And how does "for those about to nerf" know what kind of barrel he has?
WARNING-THIS IS GETTING BRUTALLY OLD!
One screw was stripped on my titan, so I Falcon Punched it. Try a Falcon Punch.
Not to mention I got the secret achievement Brass Balls for it
QUOTE(Echnalaid)
One screw was stripped on my titan, so I Falcon Punched it. Try a Falcon Punch.
QUOTE(chrisnisk)
Not to mention I got the secret achievement Brass Balls for it
#7
Nominrath
-
- Members
- 2 posts
Member
Posted 21 August 2008 - 05:16 PM
The gun is completely stock.
P.S. I would kindly like to remind those here that I am completely capable of answering questions about MY guns. Besides, I don't even know what an 'angel breech' is...
P.S. I would kindly like to remind those here that I am completely capable of answering questions about MY guns. Besides, I don't even know what an 'angel breech' is...
#8
mintee
-
- Members
- 263 posts
Member
Posted 21 August 2008 - 07:55 PM
You're probably not pulling the bolt or slide back far enough or slowly enough. If you do it too fast then the dart doesn't have time to get pushed up into the receiver before you push the slide or bolt back forward.
#9
Jabulus
-
- Members
- 62 posts
Member
Posted 21 August 2008 - 08:00 PM
Read this. It will do you good. And, incidentally, can help you fix your problem as well as increase range phenomenally, although it is a very tough mod and not for beginners.The gun is completely stock.
P.S. I would kindly like to remind those here that I am completely capable of answering questions about MY guns. Besides, I don't even know what an 'angel breech' is...
WARNING-THIS IS GETTING BRUTALLY OLD!
One screw was stripped on my titan, so I Falcon Punched it. Try a Falcon Punch.
Not to mention I got the secret achievement Brass Balls for it
QUOTE(Echnalaid)
One screw was stripped on my titan, so I Falcon Punched it. Try a Falcon Punch.
QUOTE(chrisnisk)
Not to mention I got the secret achievement Brass Balls for it
#10
SorrowX
-
- Members
- 162 posts
Member
Posted 22 August 2008 - 12:45 AM
Only two breeches out there(that I know Of, Anyways) that won't clip the tail of your darts are the Angel Breech, which is fairly complicated, and my own little design, the Sorrow Breech. just like the Angel Breech, its airtight, but the main difference is this one: its very simple to make. I'll have the Write up for it soon, so if you can be patient enough, it will be available.
You may have the balls, but I have the lack of morality!
1 user(s) are reading this topic
0 members, 1 guests, 0 anonymous users
