Jump to content


Photo

Armor Shot Mod

Another cyber stryke mod by me

4 replies to this topic

#1 NerfCrazy

NerfCrazy

    Member

  • Members
  • 497 posts
  • Location:Minnesota, 55422

Posted 21 July 2008 - 10:23 PM

Aright my armor shot didn't come with the part you put on your wrist or hold so don't let that confuse you.
Supplies
hot glue
e tape
cpvc
a cutting device for the cpvc
an exacto knife or other sharp device
rubber bands
a nail or some other small object(I used small pieces of bamboo)

Take you armor shot and remove the shield thing.
Posted Image

Then take your cpvc and cut a length of it about the same length of the old barrel.
Posted Image

Now wrap some e tape around it and make it be a good seal.
Posted Image

Now put your cpvc in the old barrel and hot glue it in. (I didn't because Iwon't need that part later)
Posted Image

Now take your box cutter/exacto knife/sharp object and cut some lines in the green piece so you can open up the gun.
Posted Image

Do the same on the other side.
Posted Image

Here is how the internals are.
Now replace the spring if you have a spring you can replace it with or add to the spring.
(The spot on my thumb is from a burn)
Posted Image
Posted Image

Now take your bamboo like I did hot glue it and add e tape to hold it together. You don't need to do this if you are using a nail. (My camera wasn't co operating(sp?) when I took these last pictures)
Posted Image

Now cut some rubber bands and tie them on the plunger handle. Then pull them to the old handle spot and put the nail/bamboo through them.
Posted Image

Then you can put some cpvc inside the old ammo holders if you want to. I didn't so that is why it isn't cut.
Posted Image

I do not have ranges since it is 10:30 as I am writing this. I hope to get ranges tomorrow but probably won't since I have to pack for my trip.

Edited by NerfCrazy, 22 July 2008 - 01:12 AM.

  • 0

#2 thaygor

thaygor

    Member

  • Members
  • 228 posts
  • Location:Harrodsburg,ky

Posted 21 July 2008 - 10:28 PM

nice mod! I can't wate to see the ranges for that thing.
  • 0
Just remember you are unique, Just like everyone else!


#3 NerfCrazy

NerfCrazy

    Member

  • Members
  • 497 posts
  • Location:Minnesota, 55422

Posted 22 July 2008 - 02:09 AM

I was playing around with it and shot pretty far and am sure it has to be more than 40'.
  • 0

#4 Forsaken angel24

Forsaken angel24

    Member

  • Contributors
  • 2,471 posts

Posted 22 July 2008 - 02:30 AM

You know what would make it really cool?

Is if you slapped on a coupler to the end and had 8 Cpvc barrels in the ammo holders and you just switch up the barrels in between shots. Or better yet, double barrels on each piece of cpvc. So you can shoot then flip the barrel and shoot again. To have the ability to do that 8 times without reloading would be pretty cool.

Also since it is called the Armor Shot. I think it should be used as a shield with the new barrels sticking out the sides. The new barrels would make blocking feasible but still very tricky.

Cool mod that inspired a strange idea.

Edited by Forsaken_angel24, 22 July 2008 - 02:30 AM.

  • 0
I don't get my kicks out of you,
I don't feel the way I used to do.
I know its bad,
After what we had,
But Iím just not the angel you knew.

#5 NerfCrazy

NerfCrazy

    Member

  • Members
  • 497 posts
  • Location:Minnesota, 55422

Posted 22 July 2008 - 02:52 AM

You know what would make it really cool?

Is if you slapped on a coupler to the end and had 8 Cpvc barrels in the ammo holders and you just switch up the barrels in between shots. Or better yet, double barrels on each piece of cpvc. So you can shoot then flip the barrel and shoot again. To have the ability to do that 8 times without reloading would be pretty cool.

Also since it is called the Armor Shot. I think it should be used as a shield with the new barrels sticking out the sides. The new barrels would make blocking feasible but still very tricky.

Cool mod that inspired a strange idea.


That is a great idea and may make this a two part mod. I am not sure what you mean but is it something like this? If not can you please clarify.
Posted Image
Posted Image
But thanks for the input.
  • 0


0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users