Homemade Buzz Bee Shells
#1
Posted 25 April 2008 - 05:56 AM
----------------------------------------------------------------------------------------------------------------------------
Materials:
Approx. 1 and a 1/2 inches of 12.5mm Clear Vinyl Tubing (CVT) Joiner (12.5mm in diameter, PVC, CPVC may work too)
2 and a bit inches of PETG
A Maverick Air Restricor
Take the Air Restrictor and cut of the three prongs and sand down flat
Next grab your PETG and cut a tiny slit in one end. If using different barrel material, cut as many slits as needed to insert the Maverick Air Restictor (next step)
Insert your air restrictor into the PETG. It should be the perfect, nice, airtight fit.
Now put the PETG into the CVT. A little hot glue around the top (careful not to get on the outside of the CVT) and your finished.
Extra Tips
1) Wrap some etape around the bottom of the shell so that it can catch on the Double Shot 'hooks'
2) Put a small bit of etape on the indide of your PETG to stop the darts falling out
3) Scrape out the Air Restrictor hole a little to make it about the same size hole as an original Buzz bee Shell.
Now for some comparison pictures:
Mine on right, Buzz Bee on left (for any dumbass who can't tell)
In the Double Shot:
No ranges but I can say much better than a stock shell, bettween 10-20ft more range. Overall I'm pleased because its hard to buy shells here an now I can have many more.
#2
Posted 25 April 2008 - 06:14 AM
I must ask though, where did you get that CVT?
Edited by xNFx 37, 25 April 2008 - 06:15 AM.
-Chief
#3
Posted 25 April 2008 - 06:16 AM
Nerf Rocket Air Launcher
#4
Posted 25 April 2008 - 06:17 AM
@Ubermech - Nitefinder Air Restrictors also work, but need to be drilled out. I'm sure some semi-thick plastic (CD Case thinkness) could be dremelled, and hot glued down and would also work. But AR's are just perfect.
Edited by Frankie27, 25 April 2008 - 06:22 AM.
#5
Posted 25 April 2008 - 07:11 AM
Very good. However, you use some uncommon materials, such as the CVT and Maverick air restrictors. I mean, I only have about six of those, and I don't want to buy another mav just to make shells.
Those maverick air restrictors are also found in most turret guns. If you have a few turret guns lieing around mod them and you have more "maverick air restrictors"
Now go play with some balls!
#6
Posted 25 April 2008 - 07:29 AM
Heh, just kidding. Good ingenuity, and congrats on the increased range!
The fourth exciting Nerf War in Fort Wayne, IN.
#7
Posted 25 April 2008 - 07:46 AM
Mine on right, Buzz Bee on left (for any dumbass who can't tell)
Err don't you mean "Mine on the left, Buzz Bee on the right?" Look at your picture again.
#8
Posted 25 April 2008 - 08:16 AM
@ xNFx37 - In Australia, we have this hardware store called Bunnings. Doesn't have Brass, PVC, CPVC or PETG. Only CVT. I think it was in a section near plastic mesh stuff. I'll have a look next time I go.
I live in Aus and its bloody annoying, but they should have PVC though but its mostly for storm water drains and such but their might be some.
Energy=Mass x Speed of light in a vacuum (in celeritas) squared
N=mc^2
Nerf=Mass of air in tank x Speed of air release in a barrel squared
"the whole damn song is a pick up line"
#9
Posted 25 April 2008 - 08:31 AM
#10
Posted 25 April 2008 - 12:10 PM
We're located in I-Don't-Give-a-Damn County, in scenic Shut-the-Hell-Up-achussets.
Maybe you're familiar with our annual charity drive where we ask for shit, and no one gives any.
#11
Posted 25 April 2008 - 01:04 PM
There must be something other than Maverick ARs that would work for this. Although I might be able to make a few bucks from the ARs I have lying around my room.
#12
Posted 25 April 2008 - 03:37 PM
#15
Posted 25 April 2008 - 09:06 PM
I guess I don't understand the rarity of CVT, because down here in Austin our Home Depots stock 15, 20, and 50 foot rolls of clear vinyl tubing. (I love Texas.) I have a roll and haven't known what to use it for, besides nesting copper in it for no reason at all. As soon as I get my hands on some brass or PETG I'll do this.
I used CVT Joiner, not CVT but I can almost guarentee the normal CVT will also work.
Err don't you mean "Mine on the left, Buzz Bee on the right?" Look at your picture again.
Lol. Now I'm the dumbass (please don't sig that)
Very interesting, and it looks quite cool. However, every modding-instinct in me is screaming out in anguish over the fact that you just PUT AN AIR RESTRICTOR BACK INTO SOMETHING!
The air restrictor is more to make that seal that stock darts do. I'm sure you could make the hole bigger but I don't need to because I'm happy with their performance.
I also wish that darts were pink and black as they appear in your uploaded images. That would be ballin'.
They are SMDTG Tagger Darts. Still really cool though.
Here some more details on them:
Name - Prototype Shell CL-S
Tested With - Buzz Bee Double Shot
Ammunition - Stefans, Taggers, Mircos
Range - Approx. 50-60ft
Material - CVT, PEGT, Mav AR
Removable After Firing - Yes (they spring out like stock shells)
Removable Before Firing - Yes (unlike stock shells)
Production Cost -
Diameter - 12.5mm
Lenght - 55mm
Other Notes
Much quieter when clattering to the floor after firing
#16
Posted 25 April 2008 - 09:13 PM
#17
Posted 25 April 2008 - 09:20 PM
Ill put a video up soon of me firing them.
Edited by Frankie27, 25 April 2008 - 09:21 PM.
#18
Posted 28 April 2008 - 06:25 PM
Edited by Blasphemy, 28 April 2008 - 06:25 PM.
0 user(s) are reading this topic
0 members, 0 guests, 0 anonymous users