Jump to content


Photo

At2k

small question

9 replies to this topic

#1 Spyder Snyper

Spyder Snyper

    Member

  • Members
  • 57 posts

Posted 02 April 2008 - 05:46 PM

How did you guys (if you did) open your at2k? With the pump thinggy glued into place? I do not have a dremel so is their any other way to open it? Thanks.
  • 0
------------------------> ! @m 0wn@g3 <---------------------------




#2 xNFx 37

xNFx 37

    Member

  • Members
  • 455 posts

Posted 02 April 2008 - 06:12 PM

You can hacksaw it open. DO NOT cut through the pump though.
  • 0
QUOTE
it also has a cock on it


-Chief

#3 ChiliPepperFender

ChiliPepperFender

    Member

  • Members
  • 599 posts

Posted 02 April 2008 - 06:57 PM

I remember reading a question about this and someone said to "Rip that shit out" or something. Which is what I did, it actually worked. All I did was pull the two halves apart. Not as clean as hacksawing but much funner.
  • 0
[The Blue Tiger][Manta Star]
WTS: Stock Crossbow. PM me if you have interest.

#4 jake44

jake44

    Member

  • Members
  • 63 posts

Posted 02 April 2008 - 07:11 PM

I usually heat up a butter knife over the stove, and that works just fine. Just be careful not to go too far in!
  • 0
QUOTE
(The infinite Shindig)
And For the record, my butt looks incredible in spandex. wink.gif

#5 imaseoulman

imaseoulman

    Member

  • Members
  • 1,005 posts

Posted 02 April 2008 - 07:54 PM

You can just crack it. Sometimes, you get lucky and it just slides right out. Just unscrew it, lift one sie and pull back.
  • 0

#6 nerfboi

nerfboi

    Member

  • Members
  • 858 posts

Posted 02 April 2008 - 11:48 PM

Just pull like h**l and it will come off.
  • 0
We Ride together, we die together, Bad boys for life.

#7 Bomberman

Bomberman

    Member

  • Members
  • 730 posts

Posted 03 April 2008 - 12:06 AM

Hey, Nerfboi, you don't have to star out cusses, especially only 'hell'. But anyway, what you should do, is take a large flathead screwdriver, get it under the piece, and then take a hammer, and hammer against the end of the screwdriver, and move it around, and then just pry it off. But trust me, it is not a good idea to heat a butter knife on the stove. It just is'nt smart. You don't want to just melt it.
  • 0
QUOTE(silentsnipe) View Post

It's not like that. I put lube on it and its the same. Its just stuck. And when I cock it back it goes farther back then usual. Also I push as hard as I can and it wont go back in. I've tried the methods and they wont work. Also pics are up.

#8 nerfboi

nerfboi

    Member

  • Members
  • 858 posts

Posted 03 April 2008 - 01:25 AM

Yeah, but still, some little kids come here. Who knows. But yeah your right. Eh, i guess I won't star it out anymore.
  • 0
We Ride together, we die together, Bad boys for life.

#9 BendyStraw

BendyStraw

    Member

  • Members
  • 183 posts

Posted 03 April 2008 - 08:44 AM

Like most materials, you will also get good results by bending it back and forth, back and forth. A paperclip will snap when you bend it too much, and I've noticed that when you try to tear plastic stuff like anti-mod glued in nerf parts, you can usually "tear that shit out" but bending it back a couple of times results in a cleaner tear, because it stresses the point that is being warped so that it gets weaker.
  • 0
WARNING - I'M BRUTALLY HARD TO READ!

#10 Ro-Sham-Bo

Ro-Sham-Bo

    Member

  • Members
  • 167 posts

Posted 03 April 2008 - 02:23 PM

I got pissed when mine wouldn't open so, I smacked it with a hammer. After a few blows, it opened right up.
  • 0
QUOTE(baghead @ Dec 31 2008, 07:58 PM) View Post

Wait a second? a Canadian National team... just won at Hockey!?

who would have ever seen that coming?



2 user(s) are reading this topic

0 members, 2 guests, 0 anonymous users