*edit* oops, I think I put this in the wrong section, I appoligize, Please move if necessary *edit*
Edited by chefdave, 16 January 2008 - 11:41 PM.
10 replies to this topic
#1
chefdave
-
- Members
- 343 posts
Member
Posted 16 January 2008 - 11:38 PM
So I got my RFS and proceed to mod it, when I tried to pry the plunger head off after dipping in in boiling water for a few seconds I did not succed. So I tried again, and again, and again, man that thing was stubborn. Eventualy I pryed it off (or so i thought) but realized that the rod had just snapped off very close to the head. So I am wondering what glue to use to attatch it back on. I was thinking plastic weld or slow cure epoxy. any one else have any ideas?
*edit* oops, I think I put this in the wrong section, I appoligize, Please move if necessary *edit*
*edit* oops, I think I put this in the wrong section, I appoligize, Please move if necessary *edit*
QUOTE(VACC @ Jul 21 2009, 08:13 PM) 
QUOTE(crispy)
Talio likes to eat his own shit.
#2
Quilan Fett
-
- Members
- 678 posts
Member
Posted 16 January 2008 - 11:41 PM
Use a screw.
SNAP Shotgun
This guy can see the future!
hasbro in a nerf war!!!!! dude the will cancel it and confinscate are guns
This guy can see the future!
QUOTE(pokemaster @ Mar 3 2009, 04:18 PM)
hasbro in a nerf war!!!!! dude the will cancel it and confinscate are guns
#3
Dayko
-
- Members
- 1,037 posts
Member
Posted 16 January 2008 - 11:42 PM
Epoxy it or Plumbers goop it. Both are vary strong adhesive's.
< One foot in death...The other in life. >
#4
chefdave
-
- Members
- 343 posts
Member
Posted 16 January 2008 - 11:45 PM
hmmm, I don't think that would be possible unless I drilled it directly through the head.
That's what I was thinking Dayko, but I am using the stock spring, a LS spring, and some other kind. I dont know If it could take the beating
That's what I was thinking Dayko, but I am using the stock spring, a LS spring, and some other kind. I dont know If it could take the beating
QUOTE(VACC @ Jul 21 2009, 08:13 PM)
QUOTE(crispy)
Talio likes to eat his own shit.
#5
Quilan Fett
-
- Members
- 678 posts
Member
Posted 16 January 2008 - 11:48 PM
There is already a hole through the plunger head.
SNAP Shotgun
This guy can see the future!
hasbro in a nerf war!!!!! dude the will cancel it and confinscate are guns
This guy can see the future!
QUOTE(pokemaster @ Mar 3 2009, 04:18 PM)
hasbro in a nerf war!!!!! dude the will cancel it and confinscate are guns
#6
Dayko
-
- Members
- 1,037 posts
Member
Posted 16 January 2008 - 11:48 PM
Depending on what type of Epoxy your using it should take the strength. I know there are Epoxy's that can take 1500 or was it 15000 pounds of pressure, I forget.
< One foot in death...The other in life. >
#7
chefdave
-
- Members
- 343 posts
Member
Posted 17 January 2008 - 12:01 AM
Oh ya, Quilan you're right, I think I will Epoxy it and put a screw though the plunger head, thanks.
I would Like to hear any other ideas any one else wants to offer though.
I would Like to hear any other ideas any one else wants to offer though.
QUOTE(VACC @ Jul 21 2009, 08:13 PM)
QUOTE(crispy)
Talio likes to eat his own shit.
#8
Quilan Fett
-
- Members
- 678 posts
Member
Posted 17 January 2008 - 12:19 AM
It actually happened to me when I replaced the spring on mine. I didn't know to heat it off, so I just cut off the peine in front of the plunger head, then screwed it back on when I was done.
SNAP Shotgun
This guy can see the future!
hasbro in a nerf war!!!!! dude the will cancel it and confinscate are guns
This guy can see the future!
QUOTE(pokemaster @ Mar 3 2009, 04:18 PM)
hasbro in a nerf war!!!!! dude the will cancel it and confinscate are guns
#9
Squishy
-
- Members
- 142 posts
Member
Posted 17 January 2008 - 11:33 AM
Should warn you, most adhesives are fine for pressure, but not so much for tension. Make sure that there is not too much friction between the walls and the plunger if you decide to only use adhesive.
Updated 6/2/08
We are the proud members of University of Maryland Nerf Activity Society, summer plans are:
Weekly games and summer Dart o' War.
WE LOVE OUTSIDE PLAYERS.
visit www.umdnerf.com for rules and forums or PM me for any questions. We always welcome outside players.
We are the proud members of University of Maryland Nerf Activity Society, summer plans are:
Weekly games and summer Dart o' War.
WE LOVE OUTSIDE PLAYERS.
visit www.umdnerf.com for rules and forums or PM me for any questions. We always welcome outside players.
#10
mystefansdontflystraight
-
- Members
- 1,176 posts
Member
Posted 17 January 2008 - 05:48 PM
Wow 
you guys must have had really hard shotguns, I am like 5.2 with pencil arms and I got it off first try...
Oh well if the screw works, thats great. If not, there is 30$ down the drain
you guys must have had really hard shotguns, I am like 5.2 with pencil arms and I got it off first try...
Oh well if the screw works, thats great. If not, there is 30$ down the drain
QUOTE(Blacksunshine @ Dec 24 2009, 02:15 PM)
QUOTE(white moonlight @ Dec 23 2009, 01:29 PM)
It's just screaming to be rearloading...
I seen a movie about that once.
#11
xNFx 37
-
- Members
- 455 posts
Member
0 user(s) are reading this topic
0 members, 0 guests, 0 anonymous users
