I just got a magstrike the other day. It didnt have that good ranges, so i tried to remove the ARs. I took a screw driver and forced them out. Everything is flush with the walls. Now when i use the clip that I think has the ARs removed it shoots a little less than the one with the Ars. (When i AR i mean the crosses and pegs in the back of the clip.)
Magstrike Ar
Started by raw shrimp, Nov 07 2007 09:23 PM
10 replies to this topic
#2
SHADOW HUNTER ALPHA
-
- Members
- 1,116 posts
Member
Posted 07 November 2007 - 09:32 PM
Rebarrel the clip (this is one of those few times where it's not a magazine). I'm not sure about why the ranges are less, but rebarreling with brass or PETG ought to make an appreciable difference. I would avoid CPVC because it can be too tight on darts.
The only commonly shared fate among us all is death. I turn to the shadows so that I may not be unfamiliar with hell's corridors when I arrive. - SHADOW HUNTER ALPHA
Founder of the Shadow Militia.
Founder of Nightshade Laboratories and The Nightshade Armament Corporation.
Founder of the Shadow Militia.
Founder of Nightshade Laboratories and The Nightshade Armament Corporation.
#3
dadude778
-
- Members
- 66 posts
Member
Posted 07 November 2007 - 09:33 PM
Make sure no plastic scraps are potruding out the back this could mess up the seal. It happened to me and I just had to sand them down.
Edited by dadude778, 07 November 2007 - 09:34 PM.
Make sure the top of your gun is parallel to the ground when firing.
Finish those other mods so I have something else to read on here.
Now have a coke and a smile and shut the fuck up.
- Forsaken_angel24
Finish those other mods so I have something else to read on here.
Now have a coke and a smile and shut the fuck up.
- Forsaken_angel24
#4
Blasphemy
-
- Members
- 355 posts
Member
Posted 07 November 2007 - 09:50 PM
If you've got some PETG put it to some good use, linkage: http://nerfhaven.com...132
When speaking about a swallow, always make sure you know whether it is an African or European swallow. It is very important.
#5
CaptainSlug
-
- Administrators
- 4,763 posts
Resident Mad Scientist
Posted 07 November 2007 - 09:55 PM
Simply hammering the pegs out isn't going to improve the performance of the gun if you're still using stock darts.
And they're not molded or glued to the barrels in any way. The way they're placed when stock the clip has a bit of leakage around them.
At the very least you have to remove the backplate from the clip, remove the rings that used to hold the pegs, seal the holes that are left behind, then glue the backplate on again.
Read more: http://nerfhaven.com...topic=7202&st=0
And they're not molded or glued to the barrels in any way. The way they're placed when stock the clip has a bit of leakage around them.
At the very least you have to remove the backplate from the clip, remove the rings that used to hold the pegs, seal the holes that are left behind, then glue the backplate on again.
Read more: http://nerfhaven.com...topic=7202&st=0
Edited by CaptainSlug, 07 November 2007 - 09:58 PM.
The little critters of nature, they don't know that they're ugly. That's very funny, a fly marrying a bumble bee. I told you I'd shoot, but you didn't believe me. Why didn't you believe me?
#6
nerfalchemist
-
- Members
- 88 posts
Member
Posted 07 November 2007 - 09:55 PM
Or for a quick fix just drill out the ARs through the holes at back of the clip.
Edited by nerfalchemist, 07 November 2007 - 10:45 PM.
QUOTE
It's like saying that your bottled water has a secret ingredient! Well yes, water!
#7
SHADOW HUNTER ALPHA
-
- Members
- 1,116 posts
Member
Posted 07 November 2007 - 11:18 PM
That's essentially what he did prior to posting.Or for a quick fix just drill out the ARs through the holes at back of the clip.
The only commonly shared fate among us all is death. I turn to the shadows so that I may not be unfamiliar with hell's corridors when I arrive. - SHADOW HUNTER ALPHA
Founder of the Shadow Militia.
Founder of Nightshade Laboratories and The Nightshade Armament Corporation.
Founder of the Shadow Militia.
Founder of Nightshade Laboratories and The Nightshade Armament Corporation.
#8
raw shrimp
-
- Members
- 160 posts
Member
Posted 08 November 2007 - 12:10 AM
That's essentially what he did prior to posting.Or for a quick fix just drill out the ARs through the holes at back of the clip.
Except I hammered mine out
#9
nerfalchemist
-
- Members
- 88 posts
Member
Posted 08 November 2007 - 08:31 PM
That's essentially what he did prior to posting.Or for a quick fix just drill out the ARs through the holes at back of the clip.
Then how did he lose range? I drilled mine out and it gets around 3-5 feet more than stock.
QUOTE
It's like saying that your bottled water has a secret ingredient! Well yes, water!
#10
raw shrimp
-
- Members
- 160 posts
Member
Posted 08 November 2007 - 10:24 PM
That's essentially what he did prior to posting.Or for a quick fix just drill out the ARs through the holes at back of the clip.
Then how did he lose range? I drilled mine out and it gets around 3-5 feet more than stock.
Thats why I'm asking.
#11
ultra920
-
- Members
- 272 posts
Member
Posted 11 November 2007 - 04:57 PM
If your using stock darts, then it makes sense. the stock's were only made for a centaind amount of air. Putting to mutch air through fucks up the projectory. Are the darts curving unusually?
There is no Ultra, only a 920.
PSN: ultra920 MGO:ultra920 shoot me an MGO invite if you play
PSN: ultra920 MGO:ultra920 shoot me an MGO invite if you play
1 user(s) are reading this topic
0 members, 1 guests, 0 anonymous users
