8 replies to this topic

[ogopogo]

I know there are many sm1500 right ups but i notised none of them were like mine and that the sm1500 doesnt seem to get as much credit as crossbows titans and longshots O my. The sm1500 is one of the all time greatest nerf guns and it deserved a better right up. So here it is!



parts and tools needed

1 Supermaxx 1500 old or new style
1 Flat headed screw driver or other prying devise
1 Philps head screw driver
4 1/2 Inch cpvc couplers
4 Feet of 1/2 inch cpvc
1 hot glue gun and a few glue sticks



Ok first you will need to open up the Sm1500.
Unscrew all the screw and pop of the caps used to hold the front and end of the gun together.
cap 1
cap 2



Now open the gun it should look like this if it does not you have a big problum. LOL


Now remove the turret from the air tank. Then take you flat headed screw driver and pry off the stock barrels. Then cut of the black thing down to were the barrel stubs are it should look like this.

Now take your 4 cpvc couplers and glue them to the barrel stubs so it looks like this.

Now you can plug the pump or do a bic pen mod to the trigger if you want.

Next put back the turret and the pump if you plugged it. It should look like this

Then screw it back together.

Now take your 4 feet of cpvc and cut it into 8 5 or 6 inch lenghts.

Now take 2 lenghts of the cpvc and hot glue them together so that there is a 1 1/2 inch lenght sticking out each side it should look like this.
Make 4 of these.
Give your self a pat on the back your done now it should look like this bad ass thing.

Edited by ogopogo, 04 September 2006 - 02:53 PM.

[Uncle Hammer]

Maybe it's just me.. but that serves no purpose. Your outer barrels don't line up with the couplers, so it really only serves as an ammo older or for looks.

[ogopogo]

Uncle Hammer, on Sep 2 2006, 08:38 PM, said:

Maybe it's just me.. but that serves no purpose. Your outer barrels don't line up with the couplers, so it really only serves as an ammo older or for looks.

Ok this is how it works you load a dart in eatch end of the cpvc clip aka the 2 lenghts glued together then once you shoot off the darts from one side of the clip you flip it around to the other side with a dart in it.

[Uncle Hammer]

Whatever you say man, it's not very hard to grab some stefans and load them each into the barrels(since you hace couplers) and slam them right back on the couplers. Whatever works best for you.

[Forsaken angel24]

Oh, I get it now. It took me a couple of times reading it over but now I understand. I thought at first the same way uncle hammer did. That all the barrels were glued together but in fact there are four seperate barrels, and each one fo them has a single barrel glued to it. Does this not make the front of the gun very heavy? The only change I would have done was to save as much of the black cover peice as possible.

Consider it added.

[z80]

Looks pretty good. I did this to my triple strike (until it broke *tear*) and it worked really well. I did one barrel CPVC, and the other pvc.

[nerfer34]

I think it would be more effective if youy just coupler modded it, but whatever.

Keep in mind that you would have had the same ROF if you did just coupler it, because the 1500 is manual rotate.

[sam]

I did this a while a go, except I cut down the the red barrel stubs all the way, and left the black shroud intact.

In that picture it just has single 7" barrels, but I also had staggered barrels in 6" and 8".

[ogopogo]

Here is me reloading and shooting it sorry its so short my camera that takes vids suckshttp://s2.photobucket.com/albums/y39/elwood91/?action=view&current=P1010001-1.flv

Edited by ogopogo, 04 September 2006 - 02:54 PM.