16 replies to this topic

[Nerfman2222]

..............

Edited by Nerfman2222, 02 July 2006 - 12:45 PM.

[Hunter]

THIRST has a good mod.

THIRST's RF20 Mod.

[Nerfman2222]

yah man thats the one im following im stuck

[THIRST]

Your still stuck...?

IM me tomorrow, 'cuase i gotta go right now.

Did you ever end up getting the screws out though...?

THIRST

[Nerfman2222]

................

Edited by Nerfman2222, 02 July 2006 - 12:21 PM.

[GeneralPrimevil]

Well the way I modded my RF20 was by removing all the screws that hold the barrels on. Then, by replacing the one in the front with a hook, all I have to do is just unscrew the hook to replace the barrels. The rotating piece (the barrel backs) then stays in tha gun at all times. No cutting of the body, but it takes longer to replace barrel assemblies. I never really used my RF20 though, especially after I became team loser. Eventually the RF20 I have will be CO2 powered and use a belt loading system. Until then, Super Soaker and NF all the way.

To reply your problem, did you cut out enough plastic to get the barrel assembly removed? Pics may help, if possible.

[Nerfman2222]

.................

Edited by Nerfman2222, 02 July 2006 - 12:21 PM.

[GeneralPrimevil]

You've probably heard this too often, but if you search for this word: pictures, you will in fact come up with a thread that I have posted in. Skip it, I'll do it for you. Here it is. Scroll down to where you find my user name has posted. There you go. If you have any questions on that, just research "posting pistures" on this website. Or ask me somehow, either way, it'll help.

[Tinkerer]

Well the way I modded my RF20 was by removing all the screws that hold the barrels on. Then, by replacing the one in the front with a hook, all I have to do is just unscrew the hook to replace the barrels. The rotating piece (the barrel backs) then stays in tha gun at all times. No cutting of the body, but it takes longer to replace barrel assemblies.

I've worked on a mod like that, except mine uses eight powerful magnets to hold it on.

[Nerfman2222]

......................................

Edited by Nerfman2222, 02 July 2006 - 12:21 PM.

[GeneralPrimevil]

Well I'm looking at my RF20 right now, for comparison. I think I see why. If you look into the barrels, on the side you cut you will notice some plastic "folded" over at 90 degrees. Maybe if you remove some, then you can tilt the barrels to the opposite side of the cut and then pull out. It's kinda hard to explain, even with pics. I'd have to be in person with the gun to show you.

Magnets? That was a brilliant idea. Too bad I stopped using the RF20. I even took the pump out and used it to replace my super soaker pump. Now I have an SM1500 pump on the RF20. Sucks like no tomorrow.

[Nerfman2222]

.......................

Edited by Nerfman2222, 02 July 2006 - 12:22 PM.

[GeneralPrimevil]

Yeah, I figured. I reread what I put and I don't even understand. Umm...If you were to look at the picture, to the upper left of the barrels there is plastic that has yet to be cut. If you were to cut about a half inch of that off, then you will be able to tilt the barrel assembly out of the gun. That may not help very much, but it's difficult to describe.

[MegaZac]

Ok, this may be a really stupid question, and yes I'm pretty new to nerf modding, but how do you get extra clips for a rapid fire 20? Do you just have to buy a bunch of the same gun?

[Nerfman2222]

.......................

Edited by Nerfman2222, 02 July 2006 - 12:22 PM.

[MegaZac]

So, no offense or anything, but it's kind of a useless mod in that sense, unless you have some other clips.

[Nazgul Lord]

But the good thing is, if you buy two guns, and clip mod both of them, when someone needs a gun you can just give them one rf20 and one clip. But I wouldn't clip mod my rf20 unless i had more than one clip.

Excellent mod by Thirst though.

Edited by Nazgul_Lord, 29 May 2004 - 07:56 PM.