NerfHaven: The Niteploy - NerfHaven

Jump to content

  • 2 Pages +
  • 1
  • 2
  • You cannot start a new topic
  • You cannot reply to this topic

The Niteploy Clip system reverse plunger reversal

#1 User is offline   nine 

  • Member
  • Group: Members
  • Posts: 111
  • Joined: 10-October 11
  • Location:Lloydminster, Alberta
  • Country:Canada
  • State:Alberta

Posted 20 January 2012 - 02:21 PM

Feeling down about reverse plungers? Well wipe off that frown, for I have created a way to bypass the terrible Nerf system!

Materials needed:
Deploy x1
Nitefinder x1
Assorted small springs
Dremel x1
Hacksaw x1
cpvc coupler x1
cpvc
Hot glue gun x1
Hot glue
Assorted o-rings
Electrical Tape
Knife x1

First, you are going to need to open your nitefinder and remove the plunger tube.

Cut it like so:
Posted Image

Remove the air restrictor spring rest, as well as the screw ports that kept the plunger tube in the nitefinder shell.

Now take the Deploy spring rest, cut off the screw port that used to keep it in place, slip it over one end of the plunger tube and glue it on.

Next, you want to cut off part of the original plunger about 6.2cm from the priming bar rest. Now add 2.5cm of cpvc to the end using whatever glue you like.

It should look like this:
Posted Image

To prime the blaster, I used half of a cpvc coupler.

Cut it like so:
Posted Image

Now give it a few wraps of electrical tape and put on two o-rings.
Posted Image

The one in the front should be slightly smaller.

Now put that piece in your plunger tube and attach it to the section of cpvc from earlier.

To have the plunger tube stay in the shell, pull the coupler as far to the front of the plunger tube as it will go.

Now place the whole assembly in the blaster, with the flat part of the deploy's spring rest pointing up.

Use epoxy putty around the flat part like so:
Posted Image

Cut the handle off of the nitefinder plunger rod and insert it in to the assembly. You should not be cutting off any more than the handle.

To place the catch, you want to cut off the entire catch area in the nitefinder, including the spring rest.

Cut off the piece that the spring in the Deploy's stock wrapped around.

Proceed to glue the nitefinder catch piece in the Deploy's stock, 6cm from the back of the main part.

It should be around here:
Posted Image

So that you can add springs to the catch, you want to drill holes that allow you to reach the screw ports.

Like this:
Posted Image

Now to make this blaster actually fire!

Cut off the deploy's trigger ramp and move it far enough back that it is touching the new catch.

Put a nitefinder ammo holder under the trigger ramp to support it
Posted Image

Now just add some extra springs around the trigger to push it back in to position.

Adding that orange piece over the trigger arm just helps keep it in place.

You have finished! Prepare to strike fear into the hearts of you foes with your new Deploy!
Posted Image
Posted Image
Posted Image

Edit: It does still accept clips.
Firing video

This post has been edited by nine: 20 January 2012 - 07:45 PM

Aeromech said:

This is my first NIC war. Well, I'm going to call it NIC because I see people playing with plumbing.


What's this? My YouTube Channel?

#2 User is offline   Flaminace2468 

  • Member
  • Group: Members
  • Posts: 16
  • Joined: 08-October 11
  • Location:Columbus
  • Country:United States
  • State:Ohio

Posted 20 January 2012 - 02:56 PM

Very nice! Maybe I could do the same thing to my longstrike, make it war-worthy!

This post has been edited by Flaminace2468: 20 January 2012 - 03:07 PM

-Yeeeeeeeeeeeeeeeeaaaaaaaaaaaaaaaaaaah buddy!!!!-

#3 User is offline   KatanasPWN 

  • Member
  • Group: Members
  • Posts: 81
  • Joined: 26-November 10
  • Location:Newark, CA
  • Country:United States
  • State:California

Posted 20 January 2012 - 03:04 PM

View PostFlaminace2468, on 20 January 2012 - 02:56 PM, said:

Very nice! Maybe I could do the same thing to my longstrike, make it war-worthy!

Don't quote the whole thread.
Welcome to hell, I'll be your waiter this evening.

#4 User is offline   Flaminace2468 

  • Member
  • Group: Members
  • Posts: 16
  • Joined: 08-October 11
  • Location:Columbus
  • Country:United States
  • State:Ohio

Posted 20 January 2012 - 03:06 PM

View PostKatanasPWN, on 20 January 2012 - 03:04 PM, said:

Don't quote the whole thread.


Yeah, just realized I did that, sorry!-fixed

This post has been edited by Flaminace2468: 20 January 2012 - 03:07 PM

-Yeeeeeeeeeeeeeeeeaaaaaaaaaaaaaaaaaaah buddy!!!!-

#5 User is offline   Exo 

  • Member
  • Group: Members
  • Posts: 383
  • Joined: 13-August 10
  • Location:SoCal
  • Country:United States
  • State:California

Posted 20 January 2012 - 03:59 PM

Very nice. I would have done it differently, bit I'm just wierd like that.

Um, you have a lot of hot glue, and you are trying to use it as a primary adhesive. Hot glue is really just plastic with a little bit of glue in it, so that it stays stuck. This isn't healthy, especially on stress areas, so you may want to consider re-gluing most of it with a 2-part epoxy or superglue. Superglue would get you the same build speed as hotglue, and you wouldn't need to let it cool.

This is an innovative piece of work, and I'd hate to see it explode.

While you're in there, you might as well add an angel breech, it can handle one now, as well as a spring, I would suggest an ace#49.

#6 User is offline   Blue 

  • Member
  • Group: Members
  • Posts: 2,220
  • Joined: 07-May 08

Posted 20 January 2012 - 04:07 PM

Does it still take clips?

#7 User is offline   Daniel Beaver 

  • HQRSE CQCK
  • Group: Moderators
  • Posts: 1,784
  • Joined: 19-September 08
  • Location:Aguadilla
  • Country:United States
  • State:Puerto Rico

Posted 20 January 2012 - 04:08 PM

I appreciate the ambition that this represents. Good job.

#8 User is offline   nine 

  • Member
  • Group: Members
  • Posts: 111
  • Joined: 10-October 11
  • Location:Lloydminster, Alberta
  • Country:Canada
  • State:Alberta

Posted 20 January 2012 - 04:08 PM

View PostExo, on 20 January 2012 - 03:59 PM, said:

Very nice. I would have done it differently, bit I'm just wierd like that.

Um, you have a lot of hot glue, and you are trying to use it as a primary adhesive. Hot glue is really just plastic with a little bit of glue in it, so that it stays stuck. This isn't healthy, especially on stress areas, so you may want to consider re-gluing most of it with a 2-part epoxy or superglue. Superglue would get you the same build speed as hotglue, and you wouldn't need to let it cool.

This is an innovative piece of work, and I'd hate to see it explode.

While you're in there, you might as well add an angel breech, it can handle one now, as well as a spring, I would suggest an ace#49.


Thanks for the input!
A stronger adhesive is a good idea, as well as the angel breech and spring replacement. Sadly, brass and springs are unavailable where I live. However, I would be very interested to see these put into action.

Aeromech said:

This is my first NIC war. Well, I'm going to call it NIC because I see people playing with plumbing.


What's this? My YouTube Channel?

#9 User is offline   andtheherois 

  • Member
  • Group: Members
  • Posts: 821
  • Joined: 13-December 10
  • Location:North Brunswick
  • Country:United States
  • State:New Jersey

Posted 20 January 2012 - 04:44 PM

This looks good, though a firing video would be nice.
The YooToobz
Photobucket

Gears said:

Winning rounds is rewarding, deal with it. We don't play fucking patty cake over here.

#10 User is offline   Exo 

  • Member
  • Group: Members
  • Posts: 383
  • Joined: 13-August 10
  • Location:SoCal
  • Country:United States
  • State:California

Posted 20 January 2012 - 06:14 PM

Once I get my power pills built, the recon that the first one will be put in will have some sort of full breech, and will use an ace 49 for the spring. It's essentially this, but with a homemade NF.

I found brass at my local do it best, you can get springs there or at an ace, you just have to find the section.

#11 User is offline   Guitarzan 

  • Member
  • Group: Members
  • Posts: 132
  • Joined: 28-December 11
  • Location:Apalachin, NY , 13732
  • Country:United States
  • State:New York

Posted 21 January 2012 - 10:20 AM

Reverse plungers are the worst thing to happen to nerf guns in the history of nerf guns. I currently have 3 broken reverse plungers, and the only modifications that caused them were simple AR removals....

I really appreciate that you're looking for ways to integrate normal plunger tubes into a gun that uses the reverse plunger in stock form. Can't wait to see the growth of this idea so that clip system guns other than the longshot can become usable guns

#12 User is offline   nine 

  • Member
  • Group: Members
  • Posts: 111
  • Joined: 10-October 11
  • Location:Lloydminster, Alberta
  • Country:Canada
  • State:Alberta

Posted 21 January 2012 - 04:22 PM

View PostExo, on 20 January 2012 - 06:14 PM, said:

Once I get my power pills built, the recon that the first one will be put in will have some sort of full breech, and will use an ace 49 for the spring. It's essentially this, but with a homemade NF.

I found brass at my local do it best, you can get springs there or at an ace, you just have to find the section.


Unfortunately, here in Canada, or at least in Alberta, there are no do it bests. I do appreciate your help though.

Aeromech said:

This is my first NIC war. Well, I'm going to call it NIC because I see people playing with plumbing.


What's this? My YouTube Channel?

#13 User is offline   makeitgo 

  • Member
  • Group: Members
  • Posts: 210
  • Joined: 17-May 11
  • Location:Ottawa, Ontario, Canada
  • Country:Canada
  • State:Ontario

Posted 21 January 2012 - 05:44 PM

View Postnine, on 21 January 2012 - 04:22 PM, said:

Unfortunately, here in Canada, or at least in Alberta, there are no do it bests. I do appreciate your help though.


Depending on where in Alberta you are, there is a 'Great Hobbies' in Edmonton that does sell brass.
"...he is one speedy bastard." ~ Cheyner

#14 User is offline   nine 

  • Member
  • Group: Members
  • Posts: 111
  • Joined: 10-October 11
  • Location:Lloydminster, Alberta
  • Country:Canada
  • State:Alberta

Posted 21 January 2012 - 06:15 PM

View Postmakeitgo, on 21 January 2012 - 05:44 PM, said:

Depending on where in Alberta you are, there is a 'Great Hobbies' in Edmonton that does sell brass.


Thanks! Edmonton isn't too far from my city, so I will have to check that out sometime.

Aeromech said:

This is my first NIC war. Well, I'm going to call it NIC because I see people playing with plumbing.


What's this? My YouTube Channel?

#15 User is offline   Exo 

  • Member
  • Group: Members
  • Posts: 383
  • Joined: 13-August 10
  • Location:SoCal
  • Country:United States
  • State:California

Posted 22 January 2012 - 02:39 PM

I've been nerfing for two years now, and although I've managed to find most of the common modding materials, it would've helped a lot if someone had told me where the stuff was. Ask some other people near you where they get stuff, and you should be good. Mcm is good, but only if your parents are cool with you buying stuff online, or you're no longer living with your 'rents.

Share this topic:


  • 2 Pages +
  • 1
  • 2
  • You cannot start a new topic
  • You cannot reply to this topic

1 User(s) are reading this topic
0 members, 1 guests, 0 anonymous users