9 replies to this topic

[sn1per]

I take no credit for the idea of making the reactor shoot darts. So, at my freinds house, (rex-techs[There? Happy? I mentioned your name. That means you, Tyler.]) So, we took it apart, and noticed a couple of ARs. Just do the usual stuff, but for the new barrel nub/housing, use a part of a airzone tek-ten. Use the part in the middle of the rotating barrel, the useless part that looks like a ninja star and is fun to chuck at a persons face (heh heh...). Sand out the middle untill a marker (or any barrel) will fit inside. Hot glue that in there, make a good seal.
Here is a pic of the front.



Then, fit that onto the o-ring part at the end of the reactor, and make another good seal. Then you are done. We had some leak problems, so use a lot of hot glue. Once again so i don't get flamed, I take no credit for the idea of making the reactor shoot darts. Ranges really depend on your darts, how hard you pump, and your barrel. I don't recomend crayolas for this mod.
Here are some finished pics.





Whoa, my hand looks weird in that pic...mabe it's because his brother crashed me into ever snowdrift he found on the tobbogan behind the quad...

Edited by sn1per, 11 February 2008 - 01:20 PM.

[sputnik]

Range?

[Carbon]

Ranges really depend on your darts, how hard you pump, and your barrel.

Range?

Five feet or 150? Even if there's variance, you can describe the difference between low and high, and tell how much of a factor those elements play.

[sn1per]

They ranges around 30 ft., with a Converted Micro and a crayola.

Edited by sn1per, 11 February 2008 - 01:46 PM.

[PointBlank]

I did that same mod to mine but I used duct tape instead of epoxy.

[PC III]

I used a 12'' cpvc barrel, put into the back. W/ 5 darts it works as a great indoor shotgun. Mine gets 80'ish.

edit: got the " ' "s mixed up.

Edited by P.C. III, 11 February 2008 - 05:22 PM.

[slowguitarman]

I used a 12' cpvc barrel, put into the back. W/ 5 darts it works as a great indoor shotgun. Mine gets 80''ish.

Too bad your mod doesn't shoot much more than 6 feet. How did you measure the range if the dart was halfway down the barrel?

[Kid Flash]

when i did this to my reactor i used a pool noodle and a .5 inch cpvc barrel inside a .75 inch cpvc pipe. i get about 70ish

[sn1per]

I did that same mod to mine but I used duct tape instead of epoxy.

I didn't use epoxy either...it's hot glue.
[/sarcasm] GET YOUR GLUE BASED ADHESIVES RIGHT, MAN!!!
EDIT: The range is the worst out of the trial, also. It was a shit stefan and we shoved it down to the back, and it took like 15 pumps to get it out. It took forever.
EDIT X2: Well, in the pic, i guess it does look like epoxy. Well i'll be darned.

Edited by sn1per, 12 February 2008 - 03:30 PM.

[Bomberman]

[quote name='sn1per' date='Feb 12 2008, 12:28 PM' post='139752']
Well, in the pic, i guess it does look like epoxy. Well i'll be darned.[quote/]
I don't think so. It just looks like a good hot glue-job. But with everyone else saying they got about 70-80 feet, I am not sure how you only got 30 feet.
EDIT: Oh wait, I'm a dumbass; I see you used a crayola barrel. I hate those damn things! Maybe it's just the way my darts fire out of crayola...

Edited by Bomberman, 12 February 2008 - 04:39 PM.