Jump to content


Photo

5 $ 5 minute 100 ft homemade

simple fast cheap and easy to make

14 replies to this topic

#1 fogeater

fogeater

    Member

  • Members
  • 6 posts

Posted 08 April 2012 - 03:17 PM

I call this the hose handle homemade

I know this has been done before but those all relied on glue to hold a piece of pvc inside the handle, but this methods; hold pressure better, is cheaper and easier to make.

This is a cheap, quick and easy to make homemade secondary that gets ranges well over 100 ft.
parts list

3/4 INCH THREADED MALE COUPLING

large tire valve

hose nozzle

1/2 inch bushing / coupling (or whatever else you want to use to connect your barrel to the hose nozzle)

bike pump

Posted Image

Posted Image
Your hose handle must have the ridge hi-lighted with green in the Handel shown in the picture above.

Posted Image
Then take your 3/4 INCH THREADED MALE COUPLING and you tire valve.

Posted Image
Then stick the thin end of the tire valve into the the threaded end of the 3/4 INCH THREADED MALE COUPLING.

Posted Image
Then screw it into the handle of the hose nozzle. (as tight as you can)

Posted Image
Finally add a couplor or bushing to the front of the hose nozzle,if you have a different nozzle you will have to couplour the nozzle differently.


If you don't want to run around with a bike pump attached to your gun remove it since there is a check valve in the tire valve it will still hold air and you can put it in your pocket as a backup shot.

I recommend holding the barrel wile firing for better accuracy.

It is very effective and cheap.

Range test with 4 pumps.

90 ft
100 ft
110 ft
97 ft
103 ft

Edited by fogeater, 08 April 2012 - 03:55 PM.

  • 0

#2 The Nerfaholic

The Nerfaholic

    Member

  • Members
  • 185 posts

Posted 08 April 2012 - 03:23 PM

Nice to see an old homemade brought back. Props! Was there any leakage from just that?
  • 0
Roses are red, And violets are blue. One day we'll cruise down Blood Gulch avenue.

#3 fogeater

fogeater

    Member

  • Members
  • 6 posts

Posted 08 April 2012 - 03:30 PM

Nice to see an old homemade brought back. Props! Was there any leakage from just that?


no the tightness of the 3/4 INCH THREADED MALE COUPLING and the hose nozzle when screwed together sandwiches the tire vale to the rim of the hose handle so well i have had it up to 100 psi left it for 20 minutes came back checked the psi and it was still at 100 psi it is a perfect seal
  • 0

#4 TxNerfer

TxNerfer

    Member

  • Members
  • 126 posts

Posted 08 April 2012 - 03:41 PM

Learn 2 grammer.
  • 0

1. Thank you, I take donations in horse/wolf porn


#5 ThatBritishGuy

ThatBritishGuy

    Member

  • Members
  • 104 posts

Posted 08 April 2012 - 03:48 PM

Does the speed that you pull the "trigger" affect the ranges, i.e. is it a similar release method to a 4B or is it instant release?
  • 0
My sales thread

Any Blaster mod or homemade that I post I can commission. Send me a PM on NerfHaven or BritNerf or email me by sam@lusher.org.uk

#6 hamoidar

hamoidar

    Member

  • Members
  • 367 posts

Posted 08 April 2012 - 04:05 PM

Does the speed that you pull the "trigger" affect the ranges, i.e. is it a similar release method to a 4B or is it instant release?

I don't think the speed which you pull the handle will matter, as the valve travel is very short.
  • 0
NerfHaven > Your control panel > Profile > Change Signature > Inserts dumb sig > What! No pictures! > Inserts next best thing: http://nerfhaven.com...howuser=114052' class='bbc_url' title='External link' rel='nofollow external'>Best thing on Nerfhaven!

#7 Ivan S

Ivan S

    Member

  • Members
  • 123 posts

Posted 08 April 2012 - 04:16 PM

Does the speed that you pull the "trigger" affect the ranges, i.e. is it a similar release method to a 4B or is it instant release?


It may or may not make a difference with this specific hose nozzle, but I've used nozzles before where it definitely does. It varies, I'd guess that ones with higher flow and shorter travel are generally better.
  • 0
You can never take nerf too seriously, but you can easily take yourself too seriously.
~Talio

#8 evilbunnyo

evilbunnyo

    Member

  • Members
  • 404 posts

Posted 08 April 2012 - 04:24 PM

The font my eyes. This is a nice revamp of the old design. Giving what it costs its not to shabby but I wouldn't go running around with that anytime soon.
  • 0
Silence is golden but duct tape is silver

#9 Nurf Doctor

Nurf Doctor

    Member

  • Members
  • 24 posts

Posted 08 April 2012 - 04:26 PM

This is a nice quick homemade. Imagine carrying several of these in the pockets of cargo shorts, all pumped ahead of time. It could turn out very amusing.
  • 0
"Spider, why you gotta be on my ceiling when I'm trying to sleep?"

#10 Buffdaddy

Buffdaddy

    Do not buy from this member

  • DO NOT TRADE
  • 824 posts

Posted 08 April 2012 - 05:22 PM

I've essentially done this before. Although yours is smaller.

Also, you're doing 4 pumps for those ranges? I might be mistaken, but that's gotta be a really high PSI you're dealing with. Most home water systems have a pressure they're built to handle, so I'm unsure of durability.
  • 0

#11 Daniel Beaver

Daniel Beaver

    HQRSE CQCK

  • Moderators
  • 2,096 posts

Posted 08 April 2012 - 06:16 PM

I've built something almost exactly like this (but I didn't post pictures, so sucks to be me!) In any case, I can confirm that these types of blasters are very easy to make, and perform extremely well. Probably a good "first homemade" for someone to build, though they are not war legal in many places.

Edited by Daniel Beaver, 08 April 2012 - 06:17 PM.

  • 0

#12 ACE11

ACE11

    Member

  • Members
  • 47 posts

Posted 08 April 2012 - 07:43 PM

You spelled coupler wrong 2 different ways in the same sentence. Either way, this is nice, but it's easier to build a bigger tank so it can be hopperable.
  • 0
Forsakenangel: Wow, 7 posts and only 2 of them have to do with the topic.
Go Nerfhaven!
Langley: I'm sorry we went off topic in your thread about exploding Easter bunnies. We'll try to do better next time.

#13 Buffdaddy

Buffdaddy

    Do not buy from this member

  • DO NOT TRADE
  • 824 posts

Posted 08 April 2012 - 08:15 PM

I've built something almost exactly like this (but I didn't post pictures, so sucks to be me!) In any case, I can confirm that these types of blasters are very easy to make, and perform extremely well. Probably a good "first homemade" for someone to build, though they are not war legal in many places.


True. It's a pain in the ass trying to use a homemade air gun at wars. You'd better have an OPV, and be willing to let people pump it with reckless abandon. Oh, and do lots of other thigns, like comparing it directly to other blasters on hand. After all, we're using compressed air. If something fails, it doesn't just break - it turns into shrapnel. That's why I question your operating psi.


You spelled coupler wrong 2 different ways in the same sentence. Either way, this is nice, but it's easier to build a bigger tank so it can be hopperable.


True, but there is a certain appeal to this. Since you can separate the pump without depressurizing, you could pump a few of these up, put them in pockets/loops in clothing, and have them for a handy backup shot. You know, that secondary pistol that turns out to be a NF Rifle.
  • 0

#14 Daniel Beaver

Daniel Beaver

    HQRSE CQCK

  • Moderators
  • 2,096 posts

Posted 08 April 2012 - 08:23 PM

You spelled coupler wrong 2 different ways in the same sentence.

i kno rite He shud be ahsamed of hiself!



Either way, this is nice, but it's easier to build a bigger tank so it can be hopperable.

There is a not-insignificant amount of tank volume within the handle itself. Hoppers work just fine.
  • 0

#15 waffleman

waffleman

    Member

  • Members
  • 10 posts

Posted 18 April 2012 - 03:44 PM

I did this with another pump a while ago. It didn't go 100ft for me, but it was close. I probably had a bad pump. Looking at yours I have to give you props definetly!
  • 0
Rednecks carry flamingos and use their redneck shotgns to hunt wild paper IN SOVIET RUSSIA OF COURSE!


1 user(s) are reading this topic

0 members, 1 guests, 0 anonymous users