Jump to content


Photo

Berserker Fusion! Daikaiju!

20 barrels, 80 feet, rearloading, and one King Ghidora head

37 replies to this topic

#1 Zack the Mack

Zack the Mack

    Member

  • Members
  • 360 posts

Posted 22 December 2009 - 11:52 PM

Posted Image
Now that I have your attention, I'd like to show you a Berserker with the air tank hooked up to the turret - the two blasters 'fused' together. 20 shots, 4B ranges, and all that good stuff. I also replaced that gawd-awful handle with one from the Longshot Front Gun and installed a little somethin-somethin in the middle of the turret. I dub this thing... DAIKAIJU! Means 'giant monster' in Japanese.

This mod is dedicated to Muttonchops, who mentioned the original idea at Apoc 09. Soon afterwards, he took a 3B barrel to the face, meaning that someone up there did not want this blaster to be made.

It's a little tough to pull apart and reassemble, so this isn't a true write-up. I'll touch on the interesting bits, which will hopefully be enough to make your own.

Posted Image
Here's a pic of the internals. The air goes out of the top of the tee, through an elbow, and into the top barrel. A cut-down neoprene washer helps prevent some air loss. I tore out the now-obsolete springer components.

Posted Image
This is the bread and butter of this mod. In a stock Berserker, the missile-launching post is attached directly to the air tank, and serves as the spindle for the turret. I sawed off the entire barrel, down to the blast chamber itself, and replaced it with a CPVC tee. Note how the tee is cut down to lie flat on the blast chamber - this ensures that the turret actuator can move correctly.

I plugged up the end of a piece of CPVC and inserted it into the tee to serve as a new spindle. To get the actuator to fit, I enlarged the hole to fit over the tee. A few wraps of electrical tape eliminated the wiggle room. I added an extra spring to the ratchety thingy so the pump could apply more force to turn the turret.

Posted Image
To kill the air restrictors, I used a 1/2" spade bit to annihilate the entire contents of each barrel. To fill the dead space and create a better seal, I hot-glued a segment of stock dart into each barrel and melted off the excess with a high-speed Dremel. Not the best solution, but it worked.
I replaced this with a new turret for rearloading action!

Posted Image
To get the air pipe to fit, I had to cut a slot in the shell and clean out some of the plastic. It's pretty straightforward - just grind away till it fits.

Posted Image
I hacked off the Oompa-Loompa-scale handle, ground the tabs off a Longshot Front Gun handle, cut a slot in the shell, and Fly Tier's Glued the handle in. Fits like a glove. The topmost screw on the new handle will be covered by the Berserker shell, so remove it first.

Posted Image
I drilled a hole in the LSFG handle's trigger tab, bent the longer firing pin to fit, and installed it all. The trigger pull is just enough to set off the blast chamber, and the internal extension spring makes the trigger spring unnecessary.

Posted Image
The finishing touches - A King Ghidora 'hood ornament' and ten feet of PETG. Why PETG? It's nice and light. Why not 20 feet? Because 10 feet is all I had!

Here's some gun porn for ya:
Posted Image
Posted Image

Check out Version 1.1, with rearloading and a basketball pump!

This mod took around six hours over two days and cost about $35, including the Berserker.

Edited by Zack the Mack, 09 January 2010 - 03:03 AM.

  • 0
Ask me questions about electronics, Arduino, and 3D printing

#2 Soothsayer

Soothsayer

    Member

  • Members
  • 663 posts

Posted 22 December 2009 - 11:55 PM

The. Tits.


I approve, tremendous work my friend
  • 0

yeah I'm that guy who made that cool thing with the cool paint.


#3 CA13

CA13

    Nude Nerfer

  • Members
  • 234 posts

Posted 23 December 2009 - 12:02 AM

Is this going to have an external air tank? By god, the secks if it did.
  • 0
Doing this as I speak. I have no idea when I got it...my DAD got it some 15 years ago, but that doesn't matter. Anyways, it keeps jerking around all over the place. I try to hold it with a rag...It doesn't look like...much.

#4 Banshee

Banshee

    Member

  • Members
  • 668 posts

Posted 23 December 2009 - 12:39 AM

Do a pump replacement, finish off the barrels and we got some competition for the Doomsayer. By the way, nice garage!
  • 0
Like my page on Facebook! PM me, I do commissions!

#5 Echnalaid

Echnalaid

    Member

  • Members
  • 981 posts

Posted 23 December 2009 - 01:17 AM

When I saw this, my belt just burst.
  • 0
There was something on the bottom of the ad that said erotyka. Sounds like something spicy -Renegademilitia15

#6 Pearson2

Pearson2

    Member

  • Members
  • 161 posts

Posted 23 December 2009 - 01:21 AM

Looks really sweet. 20 shots with a BBBB without reloading? Sweet. Plus my main comment on this gun is it looks extremly clean. Very well done.
  • 0
Crooked: Did you see that guy who singled a doomsayer?

Pearson: Why would you single a doomsayer? Thats like taking a Ferarri and putting family seating in it.



#7 CA13

CA13

    Nude Nerfer

  • Members
  • 234 posts

Posted 23 December 2009 - 01:21 AM

When I saw this, my belt just burst.


The hunger for sexy had just been satisfied.
  • 0
Doing this as I speak. I have no idea when I got it...my DAD got it some 15 years ago, but that doesn't matter. Anyways, it keeps jerking around all over the place. I try to hold it with a rag...It doesn't look like...much.

#8 Samzilla

Samzilla

    Member

  • Members
  • 91 posts

Posted 23 December 2009 - 01:43 AM

Very nice! Im assuming the loss in range is due to the dead space. I wish my berserker had come with a bbbb tank. The other tank shape/size doesn't seem to be as good, then again with 20 shots who needs the range?
  • 0
BAFF WTB Airtanks, pumps, airgun stuff

#9 JATDO

JATDO

    Member

  • Members
  • 350 posts

Posted 23 December 2009 - 06:55 AM

This is beautiful, clean and an amazing idea. Now.... Just inline clip each barrel, and you will have a banned gun
  • 0
QUOTE
I remember when some girl in my English 101 class in college tried to cite The Onion as a source for her paper. The teacher lol'd.
QUOTE
The only time I got hit was when my spotter got hit and the enemy team realized there was a marksman in the bushes

#10 NerfRogue83

NerfRogue83

    Member

  • Members
  • 646 posts

Posted 23 December 2009 - 07:31 AM

I have to say....this is very cool. Major props to you for seeing the best in each part of this blaster, and then having the ability to merge the two successfully. Like others said, do a nice pump replacement--and you have a real beast on your hands. Again, Great work!
  • 0
IRC chat: louiec3-- he offered $500 for someone to build a bomb he could send to his ex wife
Rknight-- wow......N9---your dad is in trouble now!


#11 Eh Watt

Eh Watt

    Member

  • Members
  • 265 posts

Posted 23 December 2009 - 10:11 AM

Thumbs up, man, that's just great! It fires out of the top now, too! I love it when people slap animal/monster heads or skulls on their blasters. You should paint the rest of it with 50's Japanese monster movies art. A video would be good... Again, fantastic work, very clean too!

Edited by Eh_Watt?, 23 December 2009 - 10:15 AM.

  • 0
John Hancock

#12 Hi Yah

Hi Yah

    Member

  • Members
  • 294 posts

Posted 23 December 2009 - 10:33 AM

Couldn't you just take a heat gun to some CPVC and bend it so it fits in the shell? This would remove the need of an elbow and cut down on the dead space.
  • 0
The yellow balls are also slightly smaller in diameter than the green ones.

#13 Zack the Mack

Zack the Mack

    Member

  • Members
  • 360 posts

Posted 23 December 2009 - 11:56 AM

You should paint the rest of it with 50's Japanese monster movies art. A video would be good...

It's going to get a hammered-gold paint job, and the side sticker will be replaced with a piece of a Godzilla movie poster. It needs to wait, since spraypaint doesn't come out well in cold weather. It will eventually get a video, though.

Couldn't you just take a heat gun to some CPVC and bend it so it fits in the shell? This would remove the need of an elbow and cut down on the dead space.

I suppose I could. That will eliminate the elbow, but how would that save dead space? Also, getting the length of the CPVC segments is pretty tricky.

Edited by Zack the Mack, 23 December 2009 - 11:59 AM.

  • 0
Ask me questions about electronics, Arduino, and 3D printing

#14 Vishamon

Vishamon

    Member

  • Members
  • 78 posts

Posted 23 December 2009 - 12:15 PM

Couldn't you just take a heat gun to some CPVC and bend it so it fits in the shell? This would remove the need of an elbow and cut down on the dead space.

in theory, this could work, especially since the cpvc wouldn't be operating in a pressurised capacity (ie as a tank), so you wouldn't need to worry about compromising it's integrity. However, bending pipes with heat guns is iffy at best, and bending them to the tolerances needed to both fit the shell and achieve a tight seal to the turret... well, I wouldn't try it, but you're welcome to!

EDIT: ugh, ninja'd

Edited by Vishamon, 23 December 2009 - 12:17 PM.

  • 0
QUOTE(VACC @ Dec 8 2009, 08:40 AM) View Post

I think everyone who reads or contributes to this site needs to take a big stap back and reallize we're discussing nerf guns. The fate of absolutely NOTHING important depends on what you, me, or anyone else does


#15 VelveetaAvenger

VelveetaAvenger

    Member

  • Members
  • 630 posts

Posted 23 December 2009 - 12:30 PM

I suppose I could. That will eliminate the elbow, but how would that save dead space? Also, getting the length of the CPVC segments is pretty tricky.



in theory, this could work, especially since the cpvc wouldn't be operating in a pressurised capacity (ie as a tank), so you wouldn't need to worry about compromising it's integrity. However, bending pipes with heat guns is iffy at best, and bending them to the tolerances needed to both fit the shell and achieve a tight seal to the turret... well, I wouldn't try it, but you're welcome to!

EDIT: ugh, ninja'd


It wouldn't be worth it for deadspace reasons because the rotation mech is preventing it from traveling along the hypotenuse. All you'd be saving is maybe a 1/4 or 1/2 inch on height. If somebody in the future wanted to try and keep everything in the shell, it would make much more sense to just use some type of tubing that is already flexible.

But enough conjecture, this blaster is pretty sweet as it stands. You should try to give it wings and a couple more King Ghidorah heads.

↓ Awesome! Like Monster Zero, this blaster is gonna be a total badass! Also, I didn't realize that the cpvc was bracing the turret, that's actually a good thing since it probably helps a lot with the seal.

Edited by VelveetaAvenger, 23 December 2009 - 03:27 PM.

  • 0
"I never saw Beastmaster, I just wanted to be cool..."

#16 Zack the Mack

Zack the Mack

    Member

  • Members
  • 360 posts

Posted 23 December 2009 - 02:44 PM

If somebody in the future wanted to try and keep everything in the shell, it would make much more sense to just use some type of tubing that is already flexible.

I don't think that would work - the rotation mech is actually braced against the upward air pipe. Normally, it's held in place by a green bushing on the missile tube, but once this mod is performed, the air pipe serves this purpose. I feel like a flexible tube would jam the rotation mech and eventually get sliced through, but definitely give it a try!

You should try to give it wings

Posted Image

All in good time...

Edited by Zack the Mack, 23 December 2009 - 02:45 PM.

  • 0
Ask me questions about electronics, Arduino, and 3D printing

#17 white moonlight

white moonlight

    Member

  • Members
  • 305 posts

Posted 23 December 2009 - 04:29 PM

Wow...
I really, really like this mod.
It's just screaming to be rearloading...
I'm sure this is very intimidating on the battle field.
Nice work...
  • 0
On his trec to Colonfest...
VengefulWaffle BOY, 12 KILLED IN MOUNTAIN PASS BY WILD RACCON, EXPERTS SAY HE ATTEMPTED TO HOLD IT OFF WITH NERF NITEFINDERS
POLICE SAY: ALCOHOL MAY HAVE BEEN INVOLVED
Guess who he was talking about...

#18 Gears

Gears

    The boy who lived

  • Members
  • 848 posts

Posted 23 December 2009 - 06:37 PM

Yeah.

Kinda excited to see this at the next PA War.
  • 0


WoW is destroying my life.

-Groove out.
 

 
LAWN GNOME LIBERATION FRONT
 

#19 Zack the Mack

Zack the Mack

    Member

  • Members
  • 360 posts

Posted 24 December 2009 - 12:34 AM

Rearloading and a pump replacement do seem to be pretty popular requests. Because of the sloppy way I closed up the turret, rearloading is impossible, but I could add it if someone would give me a replacement turret (wink wink).

I'm still trying to find a good place to drop a new pump. Any ideas?
  • 0
Ask me questions about electronics, Arduino, and 3D printing

#20 angelfalcon

angelfalcon

    Member

  • Members
  • 61 posts

Posted 24 December 2009 - 12:02 PM

I would maybe use the bend in one of those straws with the bendy top ends to "straw mod" the elbow and cut down on deadspace.

Also a pump replacement doesn't really have to go anywhere, just stick it in the spot the current pump is. As for rearloading, I don't know how fucked the back of the turret is. Pics would be nice.

Hope this helps you out man.

EDIT: Found a pic:

http://www.journalno...osts/straws.jpg

That's what I meant.

Edited by angelfalcon, 24 December 2009 - 12:04 PM.

  • 0
QUOTE

According to your mom, size matters. My blaster is four feet long. What about yours?

QUOTE

I measured mine and I got about 11 inches.

#21 Blacksunshine

Blacksunshine

    Member

  • Members
  • 948 posts

Posted 24 December 2009 - 02:15 PM

It's just screaming to be rearloading...

I seen a movie about that once.



This is so added to the list. Great work. That is quite a beast.
  • 0
Forgive my spelling and grammar. I post from my cell phone a lot. Sometimes when I'm on the can at work.

#22 mystefansdontflystraight

mystefansdontflystraight

    Member

  • Members
  • 1,176 posts

Posted 24 December 2009 - 02:47 PM

The problem with flexible connections on the outlet of any firing port is that they're ... flexible. When the blaster fires, it will absorb part of the energy.


I think he is reffering to the straw mod on the mav: Putting it inside the plunger tube, in this case the CPVC. Wrapping it in tape a bunch of times and gooping it into the cpvc connections might improve ranges.
I really like this, I hope beserkers come to Canada soon.

As for the pump, just do like Rork does with his decrapified MMs. The pump can be in the same place.

Just for clarification, you pump the gun, cycle the shotgun style grip at the front, and then fire?

BS: added that hilarious quote to my signature, while playing with my butthole momentarily

Edited by mystefansdontflystraight, 24 December 2009 - 02:48 PM.

  • 0
QUOTE(Blacksunshine @ Dec 24 2009, 02:15 PM) View Post

QUOTE(white moonlight @ Dec 23 2009, 01:29 PM) View Post

It's just screaming to be rearloading...

I seen a movie about that once.



#23 imaseoulman

imaseoulman

    Member

  • Members
  • 1,005 posts

Posted 25 December 2009 - 05:26 PM

Maybe I missed something...but you removed the spring plunger system? I don't see why you would do that. The best feature of the blaster is that you have long range and high ROF. You still have long range and decent ROF, but not high ROF. Was it a space issue or just an issue with the handle or is it there and I'm just mildly retarded?

It is a brilliant idea and I like it, but I think it could be better. My (unfinished) version leaves it in the center but adds a Marvelous Salvo to the turret for a Seoul Style Smackdown (wow, I feel stupider for having actually typed that...it stays).
  • 0

#24 vaan

vaan

    Member

  • Members
  • 190 posts

Posted 25 December 2009 - 05:57 PM

Why didn't you leave in the spring system, but just direct the BBBB part to the top of the turrect as you did? it would allow for both, since one fires from the top, and the other the bottom. The only problem is barrel length.
  • 0

#25 Zack the Mack

Zack the Mack

    Member

  • Members
  • 360 posts

Posted 26 December 2009 - 12:33 AM

I think he is reffering to the straw mod on the mav: Putting it inside the plunger tube, in this case the CPVC. Wrapping it in tape a bunch of times and gooping it into the cpvc connections might improve ranges.

I thought about that, but decreasing the inner diameter would also restrict the airflow. While the elbow puts in a lot of dead space, the 4B tank also moves air very quickly. I'm not sure on this - does the restricted airflow outweigh the dead space?

Just for clarification, you pump the gun, cycle the shotgun style grip at the front, and then fire?

Exactly! The pump action is still fully functioning.


Maybe I missed something...but you removed the spring plunger system? I don't see why you would do that... My (unfinished) version leaves it in the center but adds a Marvelous Salvo to the turret for a Seoul Style Smackdown.

Why didn't you leave in the spring system, but just direct the BBBB part to the top of the turrect as you did? it would allow for both, since one fires from the top, and the other the bottom. The only problem is barrel length.

I took out the springer for a few reasons. First, there's no way that pissant little plunger tube would manage to get a dart down a foot of PETG. Second, it would make the blaster harder to pump. Third, it increases the number of breakable moving parts. Finally, the LSFG handle doesn't have two triggers.

And of course you'd add a Marvelous Salvo to it, Seoul. You put Salvos on fucking everything. That's a really good idea, but 20 isn't a multiple of 3! That kind of thing bugs the crap out of me.

Edited by Zack the Mack, 26 December 2009 - 12:33 AM.

  • 0
Ask me questions about electronics, Arduino, and 3D printing


0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users