Jump to content


Photo

Easy Supa' Comfy Handles


12 replies to this topic

#1 alugilaC

alugilaC

    Member

  • Members
  • 4 posts

Posted 22 March 2012 - 12:33 AM

Tired of sanding your wood handles for hours? If you're like me you have totally forgotten your scroll saw table can tilt


Posted Image
Posted Image


I find that ~30 degrees works the best, all that is left to do is take your block o' wood handles and cut off the edges


Posted Image


Just a little sanding to get rid of the burrs, and bam! easy comfy handles.
This may be redundant to some, but I'm guessing I'm not the only one who hadn't figured this out yet.
Flames, comments, praise?
  • 0
There's nothing classier than some nice firm wood. - Stark

#2 KoRnEd

KoRnEd

    Member

  • Members
  • 209 posts

Posted 22 March 2012 - 12:40 AM

I may be totally dumb, but what exactly is the point of tilting the table of the saw? Does it make it any easier than rounding the edges down with sandpaper?
  • 0

20:07 tiredKitty living in NYC, you could spend a lot of time in Chinatown and only speak the mother tongue
20:07 tiredKitty Not a good idea, btw.

I have identified the problem: "maverick"


#3 Eik

Eik

    Member

  • Members
  • 120 posts

Posted 22 March 2012 - 01:28 AM

I may be totally dumb, but what exactly is the point of tilting the table of the saw? Does it make it any easier than rounding the edges down with sandpaper?


You can take off more material in less time.

I prefer to use a spindle sander, but you could also use rasps, files, or heck a Dremel to work down your handle blank.

Edited by Eik, 09 January 2014 - 12:31 AM.

  • 0

#4 Pause

Pause

    Member

  • Members
  • 107 posts

Posted 22 March 2012 - 03:30 AM

I may be totally dumb, but what exactly is the point of tilting the table of the saw? Does it make it any easier than rounding the edges down with sandpaper?


Like Eik said, tilting the table will take off much more wood in much less time. Correct me if I'm wrong but, I assume you still finish it off by sanding down the edges right?

Edited by Pause, 22 March 2012 - 03:32 AM.

  • 0
-Pause-

http://nerfpause.blogspot.com/

Heh.

USER WAS BLAND IN THIS POST


#5 HasreadCoC

HasreadCoC

    Member

  • Members
  • 274 posts

Posted 22 March 2012 - 09:10 AM

Like Eik said, tilting the table will take off much more wood in much less time. Correct me if I'm wrong but, I assume you still finish it off by sanding down the edges right?

Yes, exactly.
  • 0

I'm the only respectable person here. The rest of the NIC are pretty much just child molesters.


AKA: ObiWonTwo on Nerfrevolution, and most of the rest of the internet for that matter.....

#6 Meaker VI

Meaker VI

    Member

  • Moderators
  • 1,192 posts

Posted 22 March 2012 - 10:01 AM

A router might also have a useful application here; they make chamfer and round bits in a variety of styles and sizes.
  • 0

#7 djfoam

djfoam

    Member

  • Members
  • 9 posts

Posted 22 March 2012 - 03:27 PM

Thanks, I haven't thought of this before. Maybe a thread about ergonomics would be valid.
  • 0

#8 spencerak

spencerak

    Member

  • Members
  • 172 posts

Posted 22 March 2012 - 11:13 PM

Not to steal your thread, but on topic of quick, nice handles, using a cheap rasp/file hybrid thing (the kind that has a rasp on one end file on the other like THIS) I have made some super comfy RBP handles for snaps in 15-20 minutes. I have been using the one I linked earlier in this post for a while now and it does a great job, although for small curves I still have to use my Dremel.
  • 0

Holy shit it's Captain Slug.


#9 Langley

Langley

    LGLF - Since 2002

  • Administrators
  • 2,997 posts

Posted 23 March 2012 - 09:25 AM

Not to steal your thread, but on topic of quick, nice handles, using a cheap rasp/file hybrid thing (the kind that has a rasp on one end file on the other like THIS) I have made some super comfy RBP handles for snaps in 15-20 minutes. I have been using the one I linked earlier in this post for a while now and it does a great job, although for small curves I still have to use my Dremel.


That's what I use, and I have some smaller course files that I use for tight corners. Then I usually finish it off with emery cloth (which is really just a long narrow roll of sandpaper) on the curved surfaces and a foam sanding block on the more flat portions.
  • 0

You can poop in my toilet anytime champ.

2016 Nerf War Schedule
Bless you, my son. Now recite 3 New Members Guides and 5 Code of Conducts for your sins.


#10 alugilaC

alugilaC

    Member

  • Members
  • 4 posts

Posted 23 March 2012 - 08:17 PM

I tend to hurt my hands a lot, so I don't like to sand things for 10-30 minutes, also I don't have any kind of electrical sander, though I'm looking into acquiring one. This is just a shortcut I've found to avoid extensive sanding, but yes, I do find that sanded handles are a bit comfier.
  • 0
There's nothing classier than some nice firm wood. - Stark

#11 djfoam

djfoam

    Member

  • Members
  • 9 posts

Posted 25 March 2012 - 11:30 AM

I agree. Even though I have some drummer hands, sanding doesn't only hurt my hands, but also hurts my wrist. I know sanding will actually have to take place, but why not reduce time and amount of sanding? It will also give the handle a more industrial look, making it appealing to people who want to use it as a loaner primary, and not something that is already made JUST for one person's hands.
  • 0

#12 hamoidar

hamoidar

    Member

  • Members
  • 367 posts

Posted 26 March 2012 - 01:27 PM

I tend to hurt my hands a lot, so I don't like to sand things for 10-30 minutes, also I don't have any kind of electrical sander, though I'm looking into acquiring one. This is just a shortcut I've found to avoid extensive sanding, but yes, I do find that sanded handles are a bit comfier.



I agree. Even though I have some drummer hands, sanding doesn't only hurt my hands, but also hurts my wrist. I know sanding will actually have to take place, but why not reduce time and amount of sanding? It will also give the handle a more industrial look, making it appealing to people who want to use it as a loaner primary, and not something that is already made JUST for one person's hands.


Both of you need to get a Dremel and a finishing buff bit..........(http://www.dremel.co....aspx?pid=512E' class='bbc_url' title='External link' rel='nofollow external'>Dremel)
  • 0
NerfHaven > Your control panel > Profile > Change Signature > Inserts dumb sig > What! No pictures! > Inserts next best thing: http://nerfhaven.com...howuser=114052' class='bbc_url' title='External link' rel='nofollow external'>Best thing on Nerfhaven!

#13 djfoam

djfoam

    Member

  • Members
  • 9 posts

Posted 28 March 2012 - 02:17 PM

I have both of those. That factory look man, more appealing as a loner gun than one with an already custom handle.
  • 0


0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users