Jump to content


Photo

SSPB Pump Replacement and Large Tanks


9 replies to this topic

#1 iamthatcat

iamthatcat

    Member

  • Members
  • 77 posts

Posted 05 April 2012 - 04:42 PM

SSPB's need too many pumps to be really effective as a sidearm. Here's my go at a pump replacement. The factory pump is simply chopped off leaving an inlet for the new pump. I used a water gun pump from a Buzz-Bee Equalizer. It's about 1" in outer diameter and 6" long. A thinner pump would likely add pressure and perform better. A 45 degree PVC elbow is used to support the pump and act as a grip. I show 2 sizes of tank expansion. I think the smaller will be sufficient for most. I am trying a wye out on the larger with good results.

Posted Image

Here are most of the required parts. You will need some tubing to nest around the pumps outlet. I used the outlet pipe from a UMB pump. You may want some 1/2" thinwall PVC to move the grip back.

Posted Image

First let's chop up the SSPB. We'll use various methods to keep debris out of the guts. A bit of foam works well for the pump inlet. I used grease for the valve this time. A little electrical tape keeps dust out of the trigger. Twist the barrel peg out with needle nose pliers. Stuff a piece of crumpled up, wet paper towel tightly down the barrel to protect the valve from debris on this rough cut. Pull the pump handle all the way out. Chop your SSPB here.

Posted Image

Clean all the debris away and add some white lithium grease to the valve area. Try to get it behind the cross or remove the cross with a razor knife. This will keep debris out. I also removed a support boss at this point. It will get in the way of the grip later.

Posted Image

Chop a little more to get past the cross without hurting the valve. Scoop out the debris and grease with any small tool. I also used a q-tip to clean the valve out thoroughly. If done carefully there should be no need to flush the tank.

Posted Image

Chop a coupler in half, just behind the ridge.

Posted Image

I chamfered the area around the valve a little just for experimentation's sake. Glue on the coupler. While it's drying we can build and fit the tank.

Posted Image

Now onto the tank expansion. I used a PVC stub for the larger tank. I'm not sure if there is a real performance difference. It's a bit trickier to shape than a CPVC stub. Both tanks use a 1/2" PVC elbow. The larger tank uses a PVC endcap instead of a nested CPVC one. Nest a small length of PVC inbetween the elbow and the endcap for the larger.

Posted Image

Dremel the area under the PVC stub until it's paper thin.

Posted Image

Carefully slice out the center. Sorry about the recycled pic.

Posted Image

Afterwards I melted the edges a bit with a wood burning tool. This is optional. It's easy to see that support boss that needs to be removed in this pic.

Posted Image

Test fit the tank. I kept everything close to the SSPB so I could glue it in a few places for strength. Solvent weld the tank together and let it dry. I affixed the tank to the SSPB with super glue but epoxy or solvent welding is a good choice too.

Posted Image

Ok let's move on to the pump. I used a fairly slim pump but a slimmer one would raise the pressure in the tank a bit more. This pump needed the 90 degree bend chopped off to fit of course. This is still to small to nest into the SSPB's pump tube so we'll need a small section of tubing to make up the difference. The outlet tube from an old UMB pump is perfect.

Posted Image

Here it is chopped up and test fitted. I used the tape as a guide to line up the pump with a mold seam on the bottom of the SSPB. Solvent weld everything in. I added a filet of superglue to the join later for extra strength. Now we can fit the pump support/grip handle.

Posted Image

Here it is glued up. Add some glue to the elbow (or thinwall spacer) and pump face when assembling, to support the back of the pump well.

Posted Image

Chop 2 slots down the elbow. The length of the slots can be manipulated to change the grip dimensions. I just twisted the waste material with needle nose to remove it. I needed to dremel away some material from inside the elbow on the shorter grip. I also needed to add a (notched) 1/2" thinwall spacer to the longer grip. Later we can add a length of PVC and a 1/2" endcap to the grip. I used thinwall for weight. Glue the elbow both to the pump and to the SSPB for strength.

Posted Image
Posted Image
Posted Image

Now let's make the pump work. I used a piece of 1/2" PVC (conduit) with a piece of CPVC whomped into it. Shave a portion of the PVC to fit inside your pump. The CPVC is whomped in and reamed out until the pump tube slides through it freely. I affixed this with electrical tape for easy maintenance. I added an additional piece of CPVC to the end of the pump to affix my elbow and pump handle.

Posted Image
Posted Image

Shot de Money.

Posted Image

The smaller expansion takes 3 pumps for 100' ranges. The larger works a homemade wye at the same ranges but takes 5-6 pumps.

Edited by iamthatcat, 06 April 2012 - 01:47 PM.

  • 0

#2 KoRnEd

KoRnEd

    Member

  • Members
  • 209 posts

Posted 05 April 2012 - 05:40 PM

Great job! Your work with SSPB's and Jolts are amazing, and I wonder what you could do if you applied this type of thinking towards larger blasters.
  • 0

20:07 tiredKitty living in NYC, you could spend a lot of time in Chinatown and only speak the mother tongue
20:07 tiredKitty Not a good idea, btw.

I have identified the problem: "maverick"


#3 Pause

Pause

    Member

  • Members
  • 107 posts

Posted 05 April 2012 - 06:35 PM

So you finally did it! Man, this thing looks more like a homemade than a mod with it being 90% pvc!
  • 0
-Pause-

http://nerfpause.blogspot.com/

Heh.

USER WAS BLAND IN THIS POST


#4 mysterio

mysterio

    Member

  • Members
  • 249 posts

Posted 05 April 2012 - 06:37 PM

Ah-mazing as usual. How long is the hopper clip you are using? And the ranges are with domes or slugs?
  • 0

If two powerful is a problem then just go with one powerful. I guess this style of hopper will work even beyond three powerful..


15:46 *** Buff is now known as TheGdiddler
15:51 TheGdiddler I'M GONNA GRAPE YOU"

#5 iamthatcat

iamthatcat

    Member

  • Members
  • 77 posts

Posted 05 April 2012 - 06:59 PM

Thanks much!

@KoRnEd I am working towards larger stuff for sure. Jolts and SSPB's are cheap practice!



@mysterio The hopper is about 8" and feeds perfectly with 1.1" - 1.2" darts. I'm using glue domes but super crappy foam. With good foam and slugs ranges should be the same or better.
  • 0

#6 ShaNayNay

ShaNayNay

    Member

  • Members
  • 254 posts

Posted 05 April 2012 - 07:29 PM

Hey cat, great job on the writeup! If I have any extra SSPB's after my Hunter integration project I'll definitely do this to at least one, these are amazing! My only problem is that I only have one extra pump on me, and it sucks. Hopefully I'll pick up some good stuff on my next thrift store raid :)

I know I'll folloe this write up for the CPVC barrel and coupler, but I may have to take a different approach on the tank using vinyl tubing so I can keep things smaller. Again, nice job on everything.

Edited by ShaNayNay, 05 April 2012 - 07:31 PM.

  • 0

New Jersey is fuckin weird


#7 Funky Mutha Facko

Funky Mutha Facko

    Member

  • Members
  • 118 posts

Posted 05 April 2012 - 07:45 PM

I am a fan of that cat. You will be seeing the funky version of this as soon as I finish current projects. Thank you. Wish I could have beaten ya to if.
  • 0
HARDCORE NERF!

#8 hamoidar

hamoidar

    Member

  • Members
  • 367 posts

Posted 06 April 2012 - 11:56 AM

Wow! You are a genious with the these small guns. I can never seem to be precice enough to do such small and detailed mods. How strong is the connection of the pump to the original gun? It seems as if it would be pretty easy to accidently hit it on something(or someone), and the pump would crack off. Don't get me wrong, I swear by super glue, but that pump outlett tube is pretty small/weak.
  • 0
NerfHaven > Your control panel > Profile > Change Signature > Inserts dumb sig > What! No pictures! > Inserts next best thing: http://nerfhaven.com...howuser=114052' class='bbc_url' title='External link' rel='nofollow external'>Best thing on Nerfhaven!

#9 iamthatcat

iamthatcat

    Member

  • Members
  • 77 posts

Posted 06 April 2012 - 12:17 PM

The pump should end up supported by a fair amount of material. Truthfully the larger tank version has a fault there. I clumsily repositioned the pump during gluing and it dried slightly proud of the sspb's pump tube. If you glue it in good it's tough. You have to add glue to the face of the pump and the sspb's pump tube/nested pipes combo. It'll be the way you'll do it when you try it.

edit : I added a pic that was needed there. Thanks hamoidar.

@ mysterio - Here's a better pic of that wye.

Posted Image

Edited by iamthatcat, 06 April 2012 - 02:16 PM.

  • 0

#10 idleninja

idleninja

    Member

  • Members
  • 24 posts

Posted 09 April 2012 - 09:58 PM

Sweet writeup, very detailed + easy to follow. I bought 6 SSPB's on clearance so I will be doing this to all of them!

How strong is the connection of the pump to the original gun? It seems as if it would be pretty easy to accidently hit it on something(or someone), and the pump would crack off.


I was thinking the same thing, so I built the pump INTO the handle, then ran a tube from the pump into the SSPB:

Posted Image

Posted Image

Posted Image

The pump is from a SuperSoaker Max-D 3000 2-pack from target. The pump handle fits perfectly into 1/2" PVC, didn't even have to glue it in.

Edited by idleninja, 11 April 2012 - 12:35 AM.

  • 0
Sig?


0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users