- NerfHaven
- → zxnam's Content
zxnam's Content
There have been 85 items by zxnam (Search limited from 03-December 96)
#112418 Zxnam's Cpvc Night Finder System
Posted by zxnam on 21 June 2007 - 07:27 PM in Modifications
#112285 Zxnam's Cpvc Night Finder System
Posted by zxnam on 20 June 2007 - 10:44 PM in Modifications
#112036 Zxnam's Cpvc Night Finder System
Posted by zxnam on 19 June 2007 - 05:19 PM in Modifications
#112028 Zxnam's Cpvc Night Finder System
Posted by zxnam on 19 June 2007 - 04:39 PM in Modifications
So the barrel in the laser connects to the coupler? I've seen SSPB's in that position, but never another barrel.
Correct, Its more for fun than anything but in an indoor war it can save your life especially when you have another shot totally ready to shoot in 2 seconds.
#112021 Zxnam's Cpvc Night Finder System
Posted by zxnam on 19 June 2007 - 03:59 PM in Modifications
For the Double barrel you will need:
Two 3" cpvc lengths 1/2" and one 3/4" section(approximate for both)
Two 1.5" lengths of 3/8" vinyl tubing
Electrical Tape
Glue
1. Cut both vinyl tubing like so, so the tubing will fit.
2. Fit both pieces into the 3/4" length of 1/2" cpvc and glue it down good.
3. Wrap E-tape around the the end of the vinyl tubing so it fits snugly.
4. Slip the 2 sections of cpvc over the vinyl tubing.
5. Glue it down good. Connect the 2 with glue also.
END OF PART I
For Part II you will need:
10" of 3/8" vinyl tubing
Drill
Electrical Tape
Glue
1" stub of 1/2" cpvc
3" section 1/2" cpvc
1. Cut a 1/2" hole in the shell just forward of the trigger.
2. Wrap E-tape around the end of the vinyl tubing so it fits snugly on the cpvc.
3. Slip the cpvc over the vinyl tubing on one end and glue it in.
4. Cut laser like so, opening it up helps.
5. Slide Vinyl tubing through hole and glue the other end in.
6. Position the barrel so you can connect the other end to the coupler, glue it place.
And your done!
#103831 Your Weapon Setup.
Posted by zxnam on 03 May 2007 - 08:24 PM in Off Topic
Primary: Cpvc'ed Mav
Secondary: Nightfinder (soon to be my crossfire)
Or
Primary: Nightfinder
Secondary: None, I like to be mobile I will occasionally carry a second NF though.
Hopefully I can get my magstrike for my primary soon.
#102776 Yet Another New Guy
Posted by zxnam on 28 April 2007 - 01:20 PM in General Nerf
#112330 Viva La Difference!
Posted by zxnam on 21 June 2007 - 09:01 AM in Articles
#112349 The Thunder Clip
Posted by zxnam on 21 June 2007 - 11:41 AM in Modifications
To start I redid the Steps 8-9.
I found this metal bead that had an OD of 1/2", It was perfect.
I just glued it into cpvc and then into the back and it worked great.
Then I made a handle to slide the bolt.
It started out as 2 clips from a rope light. I glued them on.
Then I attached a metal L piece to it. Simple but effective.
And some random breech pics.
#112290 The Thunder Clip
Posted by zxnam on 20 June 2007 - 10:52 PM in Modifications
Right, right. I got the copper. But your slide is inside the breech. Cool.
Yeah, The good thing is is that because of the lip on the one piece keeps it 100% airtight. Also this is a super easy breach to put on pratically any gun. With the cpvc on the back I can put it on any gun with a cpvc coupler. And, I can make different brass barrel lengths for each gun's needs.
Carbon, It feels great, I am putting on a slider to make it easier. I didnt see that there, that it kind of like mine but i think mine is less complicated.
P.S. Does anyone know what that part is?
#112256 The Thunder Clip
Posted by zxnam on 20 June 2007 - 08:15 PM in Modifications
You Need:
-1/2"repair sweat piping copper
-1/2"nut
-17/32 Brass
-piece I don not know(someone help me)
-1/2" cpvc coupler
-1/2" cpvc pipe
-glue
1. Take your copper pipe and attach the piece I am trying to find out. The pipe should me at least 4" long.
2. Mark the pipe for the dart entry to the breech. Refer to above picture.
3. Cut the hole in the copper, I used a mini roto zip.
4. Put the coupler on the end of the copper, it should be a good fit, glue in good.
5. Cut a 1" section of cpvc and hollow it out really good so it will fit over the brass, then cut it in half.
6. Place a length of brass that works good in the gun you want to use(it has to be 17/32 though) into the copper pipe.
7. Slide 1 of the cpvc pieces over the brass until the coupler keeps it in place nice and snug. Mark it and then pull it out and glue it in.
8. Hollow out the nut.
9. Slide over the cpvc and glue into the piece I do not know the name of.
10. Put on a clip system you like.
Your Done.
So when the dart enters you shut it(of coarse) the dart is pushed back but enter into the brass by the brass. There is a lip of the piece i dont know of the keeps it airtight. It is held in place by the cpvc coupler/cpvc.
Open Breach
Closed
Also the steps 8-9 can be bettered I am sure. Hope you like it! Completion time is easily less than 2 hours for sure. I hope to get a bbb or some other higher powered gun to try this on soon. Questions/comments?
#112284 The Thunder Clip
Posted by zxnam on 20 June 2007 - 10:41 PM in Modifications
So it's pretty much a BS-9 breech with the clip attached to it?
Not really, Mine has copper and a different loading method.
#105689 Switch Shots Ultra Mod
Posted by zxnam on 15 May 2007 - 04:22 PM in Modifications
I dont understand why nerf makes a fake air tank!
I am quite sure that that was used for water so if I am correct that bottle isn't doing anything for the gun, please correct me if I am wrong though.
#108354 Supermaxx 3000(blue) Modification
Posted by zxnam on 30 May 2007 - 04:45 PM in Modifications
#158119 Stefan Issues
Posted by zxnam on 05 June 2008 - 11:29 AM in Modifications
1. Take Foam and burn a deep hole and then fill all the way with hot glue so it spills out the top
2. Have a premade ice cup out and ready.
3. Spin the dart in the ice until the dome is solid and perfectly made.
And now you have a dart that is perfect for indoor wars in my opinion. It it also great for secondary's outside. The first darts wont turn out till a dome shape hole is melted in the the ice, so i use a hot glue gun for that.
#109397 Stats 10 Dart Blaster
Posted by zxnam on 04 June 2007 - 04:20 PM in General Nerf
#110693 Spring Size Question
Posted by zxnam on 11 June 2007 - 01:17 PM in Modifications
The spring is to short so it will still work but have a very loud noise.Would I have to do anything to the ace #49 like tempering?
#110750 Slapp
Posted by zxnam on 11 June 2007 - 05:30 PM in Modifications
#130865 Secretivness Of Mods
Posted by zxnam on 28 November 2007 - 04:55 PM in General Nerf
#109468 Secret Shot 1 Mod
Posted by zxnam on 04 June 2007 - 09:59 PM in Modifications
#109472 Secret Shot 1 Mod
Posted by zxnam on 04 June 2007 - 10:12 PM in Modifications
#110733 Rifle Maverick
Posted by zxnam on 11 June 2007 - 04:23 PM in Modifications
#110442 Pvc And Cpvc Help!
Posted by zxnam on 10 June 2007 - 02:32 PM in General Nerf
Ok....
1.So what your saying is that 17/32 brass would fit inside of 18/32 inside of 19/32?
2.And yes i am planning on using shells, would they work with brass. As in, brass breech and brass shells? And if it would help i need it for a titan...
3.And CaptianSlug, i head that 1/2 CPVC has the appropriate ID for stock darts..... Is this true?
THANK YOU SHADOW!!!!
1. Yes but dont go looking for 18/32 brass, its 9/16
2. I am not sure if it would work, you may need an ejector.
3. Cpvc fits the the body not thehead of stock darts. The breack wont work if you use stock darts.
#103888 Nitefinder Plungerhead
Posted by zxnam on 04 May 2007 - 06:48 AM in Modifications
#113065 Nitefinder "dog-rifle"
Posted by zxnam on 25 June 2007 - 08:50 PM in Modifications
#102774 My Maverick Mod.
Posted by zxnam on 28 April 2007 - 01:11 PM in Modifications
#117226 Monster Mini Rocket Bazooka
Posted by zxnam on 26 July 2007 - 11:43 AM in General Nerf
#110878 Modification and Paintjob Pictures
Posted by zxnam on 12 June 2007 - 02:40 PM in Modifications
Maveric, Cpvc'd and turret glued on.
#104578 Modding A A Crossfire, Help Plz
Posted by zxnam on 08 May 2007 - 06:12 PM in Modifications
#110672 Maverick Cocking Handle Repair Guide
Posted by zxnam on 11 June 2007 - 08:19 AM in Modifications
#111898 Maveric Slide Repair
Posted by zxnam on 18 June 2007 - 05:51 PM in Modifications
- NerfHaven
- → zxnam's Content
- Terms of Service and Privacy Policy
- Code of Conduct ·