That was disturbing until I realized what you actually meant.
In the Meadowvale clan wars. 2 players will killed in Nerf drive bys(sp?)
The first was taken out while camping someones house. He was hiding to close the curb. The cars speed slowed down at the right time. Two rapid fires hanging out the front passenger window and the rear right passenger window. 40 darts later he had no chance.
The other player taken out was walking to work and again walking to close to the curb and my team just pulled up beside her and out pops the rapid fire. I think my team didnt even keep going they just pulled up beside her and stopped but indeed another quality hit.
- → Airsoft999's Content
There have been 242 items by Airsoft999 (Search limited from 14-October 93)
EDIT:: Yooper was imitating Stefan http://www.nerfhq.co... nerfer&start=0
So you must be young to believe that your brother can nerf with you eventually when he is older and you are still living at your home.
My new brother was born earlier today and I'm so happy cause I also have twin brothers. And in a couple of years we can have 2 on 2 whenever! But the most important part of the post is that my baby brother is born.
Hasbro went to check out one of their nerf wars.Where did you get to try it? Yeah they said late summer/early fall.
I have held one in my hands and fired it, and I know that it owns. It's really good stock, same with dart tag. I dunno about modding, you'd have to cut out a lot of the case where the turret comes out, if you look at the pictures. Though the Hasbro people said late summer/early autumn before it was out. But that could have just been me. I think other people could back me up on that.
I think that it looks pretty sweet,even if it sucks I think I will pick on eups just cause of the looks. If I dont like it it looks like it would be big enough to intagrate something good in it.
Don't worry, Tidge, we love you.
Well the ammo-holder is clicked either up or sideways, allowing that certain barrel to shoot (as you probably know) but I think you can have it half-and-half, but it would be weak.
That's a nice mod, and it's very clean. Well done. Does it shoot both darts at the same time, or can you switch between the two barrels? That would be schweet.
Rereleases don't improve performance- just a new paint job sometimes. Also, Captain knows that the AT3K was rereleased- he means there will be other big rereleases, too.
AT3k's still being sold, buddy. I'm not sure that Hasbro would make a re-release of it. They don't really have anything to improve on it either (I would like it to fit my hands better though.) If they did, it could be nice, but I don't see that for a while.
Blink 182. Go ahead, laugh and say how my music taste sucks. I like their music, and Travis Barker rocks your face off. Besides, music debates are worthless, because in the end, everyone's music taste sucks.
"Dammit", "Carousel", "Dick Lips", and "Stay Together for the Kids" are my personal favorites.
1.) Find a suitable barrel- you'll want about ten inches of whatever you need. If you are using stock micros, or mega stefans, use SCH40 PVC (found in most hardware stores) If you use micro stefans, use PETG, CPVC, SCH80 PVC, copper, or brass. If you use brass, nest 3.5 inches of 17/32" in 10 inches on 9/16" brass. Then, cut down/hollow out the barrel, and glue/stick your barrel onto the stub or push it into the original barrel. Then make sure it is airtight. Use a ramrod to load the dart.
2.) Cut down all but 1/2"-1" of the original barrel. Wrap the stub in tape, until a coupler fits snug on it. The coupler should be glued on airtight. Make sure the coupler fits the barrel material you choose to use, i.e. copper coupler for copper, PVC coupler for all PVC and brass, and CPVC coupler for CPVC. The barrel you choose to use should be the same as what I mentioned in mod 1. However, don't glue the barrel into the coupler- you WANT the barrel to be removable to increase ROF. To reload, take the barrel out of the coupler, and push the dart into the back of the barrel, and then put the barrel back in.
** For brass and a PVC coupler, put the brass inide some PVC so the PVC fits in the couper. Brass does not fit in a coupler by itself.
3.) Cut down the barrel like in mod 2. This mod is only for if you are using micro stefans or stock micros. Then, insert a hollowed out crayola marker in the stub for stock micros, or 4 inches of 17/32" brass in the stub for micro stefans. Make it airtight. Then glue a PVC coupler around the brass. Then make a barrel extension out of 10 inches of SCH40 PVC (stock micros) or 10 inches of 9/16" brass inside 6 inches of SCH40 PVC. To load, push your dart into the smaller constricted barrel (the marker) and then slide the barrel extension over the crayola or 17/32" brass and into the coupler.
4.) Make a breech, as shown in Zero's breech design in the Homemades section of this site.
I'd not recommend no. 1 for its slow reload, but the other three are all good choices. Pictures and more thorough directions can be found by searching around the forums and on Google. You can PM me if you have any more questions.
I am not anxious to get excited over either of the guns, because of the bust that the Mav was.
First, you don't care about looks? I'd buy a sucky gun if it was cool. Also, the FireFly has the old plunger system, not the one the Maverick had, so you can expect better performance, i think, because the old plunger system allowed a larger plunger tube per unit space.
When you say it shoots better than a NithFinder, I hope it shoots a LOT better than a NiteFinder. I gun as kewl as you describe it should be rather strong. I wonder how big the plunger tube is?
First off, the Firefly is just flat out cool. I have a feeling it's going to be a gun thats single barreled because the turret is being held in so it blocks the bottom barrels kinda like the maverick, so you're not going to be able to do much with barrel replacements. Hersh really liked that idea, and being that he's smaller in stature, it fit him better then the crossbow. I'd make a bet that single barreled it will shoot better then the Nitefinder.
Super Maxx 750
SuperTech Rerelease- I hope
Actually, some old NF ammo was thinner than others... I have about 9 darts that do work in my ner NF, and about 9 that don't.
The new nite finders ammo is regular micros and the old ones used airjets. The old ones won't fire because they are to fat. You need to drill the air restrictors out to get them to fire.
EDIT; Please use black letters, your killing my eyes
Ah, you'll get the hang of it eventually. Welcome.
If you plan on modifying it to put on da hurt- AT3000
For plain ol' fun and games- get the Maverick. Just don't open it up. The little orange piece may get you to cry once you understand more about nerf.