- NerfHaven
- → Eleven11punk's Content
Eleven11punk's Content
There have been 9 items by Eleven11punk (Search limited from 03-December 96)
#364475 Ballzooka 94 mod
Posted by Eleven11punk on 21 February 2020 - 01:30 PM in Modifications
However there was no noticable difference for me in range..haha oh well. I may mess with it some more; try to get a better seal where the white tube meets the barrels. It was fun for my first nerf mod. If I ever do the barrel extension I'll be sure to post it in mods section. Thanks again!
#364431 Ballzooka 94 mod
Posted by Eleven11punk on 30 January 2020 - 11:50 AM in Modifications
You don't put any on the back. You put one in the middle that matches the ID of the skirt seal (7/8") so it stays put, and you put one on the front that's just large enough (1 1/4") to hold the skirt on.
Did you use a hole saw to cut the poly? I was planning on using one but not sure if the center drill bit part would be larger than the 9/64 hole you said to drill for the screw.
#364426 Ballzooka 94 mod
Posted by Eleven11punk on 27 January 2020 - 07:24 PM in Modifications
#364409 Ballzooka 94 mod
Posted by Eleven11punk on 24 January 2020 - 09:07 PM in Modifications
The only mod writeup I've ever seen for that blaster is the one I did. I'm not sure it's a great mod, but it exists.
To answer your questions, it's a manual plunger blaster, sometimes called "push-pull" blaster, for obvious reasons. Lately I've seen this style of blaster called HAMPs, after Kane's blaster of that name. I'm not sure about extending the inline clips. I've never seen it done.
Hey so I ordered the rubber seal but reading over your instructions for the polycarbonate I'm a little confused.
Are there two pieces I should cut? (One for front and back?)
#364406 Ballzooka 94 mod
Posted by Eleven11punk on 24 January 2020 - 12:13 PM in Modifications
Click "Image Archive" at the top right. They were a victim of the imageshack apocalypse a few years ago, but survive in that archive.
Great! I couldn't see it because I wasn't on fullsite mode. Okay so now I just need to find another cheap, available ballzooka. A broken one I can part out.
#364405 Ballzooka 94 mod
Posted by Eleven11punk on 24 January 2020 - 12:02 PM in Modifications
If you are looking for more old ballistic ball ammo, I can confirm that the following on Amazon are an exact match. Work for my old Master blaster.
https://www.amazon.c...i_Qc6dEbHZNECM6
Awesome thanks! Now I don't have to order from AliExpress and wait a month for p active golf balls
#364371 Ballzooka 94 mod
Posted by Eleven11punk on 03 January 2020 - 11:37 AM in Modifications
I recently just surprised the kids with the ballzooka and they were intimidated by the size and noise alone even though their blasters are far more powerful...hilarious.
It may be awhile before I mod. I'm going to try a few other blasters first.
Thanks for the response and input!
#364351 Ballzooka 94 mod
Posted by Eleven11punk on 21 December 2019 - 12:18 AM in Modifications
I recently got an original ballzooka for 8 bucks and was thinking of modding it. Why you ask? Nostalgia.
I work at a children's home where the kids love to play Nerf (ages 5 to 17) in the house. A ballzooka was my first ever Nerf gun and I doubt these kids have ever seen one, let alone have heard the ridiculous clanging noise as ball ammo larger than they've ever seen is grenaded at them.
The gun works about a good as any ballastic gun does....ha... However, my curiosity is getting the best of me and I wanted to run some ideas up the flag pole before I ruined this gun, especially since I've never modded a gun before.
1) Is this considered a spring action gun or air pump? You don't pump it but I guess you push the air...so a plunger gun? I wanted to see if I could tighten up the gun inside to seal up any places air leaks out...basically more air power and either harder hits or farther distance.
2) Just humor me a little more... I also was thinking how awesome it would be if I could make the barrels longer....maybe buy another ballzooka, chop the barrels, chop the tops of the original gun barrels, connect both sets of barrels, replace springs with longer ones and hold twice as many balls (not too concerned with accuracy ... I'm aware the barrels wouldn't be perfect).... Would the gun have enough power? It sure as hell would be front heavy.... But intimidating.
Thanks in advance.
#364349 Ballzooka-compatible ammo?
Posted by Eleven11punk on 20 December 2019 - 03:21 PM in General Nerf
20 pcs Yellow Foam Golf Ball Indoor Exercise Ball Eva Solid Color https://www.amazon.c...i_MZs.DbZ4Z9EFD
- NerfHaven
- → Eleven11punk's Content
- Terms of Service and Privacy Policy
- Code of Conduct ·