Jump to content


YEETthatdart's Content

There have been 6 items by YEETthatdart (Search limited from 11-November 96)


By content type

See this member's

Sort by                Order  

#363936 My Reactor Mod (Elite Single Shot/Shotgun Mod)

Posted by YEETthatdart on 25 May 2019 - 06:43 PM in Modifications

I forgot : the reason you should put the coupler on the back is to make sure some darts don't slide all the way back into the air chamber. (it destroys the darts when you try to fire the gun,




#363935 My Reactor Mod (Elite Single Shot/Shotgun Mod)

Posted by YEETthatdart on 25 May 2019 - 06:41 PM in Modifications

I made a brass barreled reactor that can be single shot or multi shot depending on how many darts you put in it. It requires you to cut out the white AR piece in the blaster, and then I suggest if you have any 1/2 cpvc (about 2 inches of it) to get that and a cpvc coupler and attach that to the back end of your brass and glue it in place. after that hammer the cpvc down the front of the gun (I suggest removing the spring pusher for balls instead of cutting it apart)and then place the cpvc part into the hole where the AR was. Then to center the barrel and hold it in place you should cut a hole into a reactor ball and wedge it on to the end of the brass side. The general range depends on the type of dart, accufakes work best IMO. The duct tape on the back of the gun is cause it has a broken screw port.

Attached Thumbnails

  • IMG_20190525_193810.jpg
  • IMG_20190525_193816.jpg
  • IMG_20190525_193759.jpg
  • IMG_20190525_193742.jpg
  • IMG_20190525_193740.jpg



#363934 Nerf Rival Apollo to Elite Mod

Posted by YEETthatdart on 25 May 2019 - 06:23 PM in Modifications

I am not sure due to me not having a chronograph, but the range is about the same as the apollo firing a rival round if the bullet is newer




#363933 Nerf Rival Zeus SImple Hopper Mod

Posted by YEETthatdart on 25 May 2019 - 06:20 PM in Modifications

Hi, besides the occasional need to lean the gun down in order to feed the rounds I have had no jams with it.




#363556 Nerf Rival Apollo to Elite Mod

Posted by YEETthatdart on 13 December 2018 - 10:42 PM in Modifications

This is a mod that allows you to fire elites out of an apollo as a front loader. All you need is a buzzbee shotgun shell that has the back drilled out (AR removal),electrical tape, and an apollo.

 

Just wrap the buzzbee shell with some e-tape until you can push it in the front of the apollo with only enough hold to keep the shell in place and load an elite into the shell like normal, then fire. 

Attached Thumbnails

  • IMG_20181213_203936.jpg
  • IMG_20181213_203918.jpg
  • IMG_20181213_203909.jpg



#363522 Nerf Rival Zeus SImple Hopper Mod

Posted by YEETthatdart on 24 November 2018 - 11:01 PM in Modifications

I made a basic removable hopper for the nerf zeus using some 3/4 inch pvc that was bored out to around 5/8 inch ID that I bought from home depot.I used around 1 1/2 feet in total to make this,I also used 2 elbows and a coupler on the end,I also added an end cap with a chunk of leftover pvc to make sure the rounds don't fall out.The pencil is to hold down the mag lock on the zeus,this can be removed easily but I left it in.This holds around 16 rival rounds but can be extended around the gun,but may require a fan similar to OutOfDart's HIRricane mod,I just made this to reload on the go and it works pretty well for a gravity fed hopper.

Attached Thumbnails

  • IMG_20181124_205047.jpg
  • IMG_20181124_204952.jpg