Eraser475's Content
There have been 85 items by Eraser475 (Search limited from 03-December 96)
#324939 Modification and Paintjob Pictures
Posted by
on 30 December 2012 - 07:23 PM
in
Modifications
Here's some stuff I got done the last few days:
#323135 Homemades Picture Thread
Posted by
on 28 October 2012 - 06:33 PM
in
Homemades
Shortshit got a stained handle:
#323125 Buzz Bee Cougar
Posted by
on 28 October 2012 - 02:26 PM
in
Modifications
I have one of these, and I really like it. There is an ar in the front of the plunger tube that just falls out if you poke it with a small screwdriver. Nice Mod!
#320369 Augsational!
Posted by
on 11 August 2012 - 10:38 PM
in
Nerf Wars
I really need to get to a war for once. It sounds like a great time, but I am busy and its a 3 hour drive.
#320359 Homemades Picture Thread
Posted by
on 11 August 2012 - 08:45 PM
in
Homemades
I made a Snap pistol, based off of GMLindustries' "NOMshot". ()
I call it "Shortshit"
I call it "Shortshit"
#319080 Homemades Picture Thread
Posted by
on 24 July 2012 - 09:47 AM
in
Homemades
Took the spring out of my Snapbow and slapped some bow arms on it. I used this: http://nerfhaven.com...showtopic=20195
I haven't measured ranges yet.
I haven't measured ranges yet.
#319053 Modification and Paintjob Pictures
Posted by
on 23 July 2012 - 07:25 PM
in
Modifications
Belongs in Homemade. My bad.
#319006 First annual Parabolic Toys contest!
Posted by
on 22 July 2012 - 07:52 PM
in
Homemades
I should have seen this topic earlier. I'm gonna try and throw something together. PM incoming.
#315601 Homemades Picture Thread
Posted by
on 12 May 2012 - 05:54 PM
in
Homemades
Made a Wye for Megas (Compared to a regular DMK Wye)
#315350 Modification and Paintjob Pictures
Posted by
on 07 May 2012 - 08:03 PM
in
Modifications
Very Sexy ^
Added a tactical rail from a busted Reflex slide to my custom Xploderz Xblaster 200:
Added a tactical rail from a busted Reflex slide to my custom Xploderz Xblaster 200:
#315277 Add a trigger to the Xploders Xblaster 200
Posted by
on 05 May 2012 - 08:28 PM
in
Modifications
BUMP
Instructions for adding a stock added:
Instructions for adding a stock added:
#315258 Modification and Paintjob Pictures
Posted by
on 05 May 2012 - 04:31 PM
in
Modifications
Added a stock to my Xploderz with a trigger:
Just 2 screws holding a 1/2" PVC endcap on the back of the blaster:
Just 2 screws holding a 1/2" PVC endcap on the back of the blaster:
#314687 Rockets for Nerfers
Posted by
on 22 April 2012 - 09:52 PM
in
General Nerf
Congrats! I hope everyone enjoys their rockets!
#314635 Add a trigger to the Xploders Xblaster 200
Posted by
on 21 April 2012 - 11:16 AM
in
Modifications
Really glad this popped back up here right when I found two of these babies. There's one thing that bugs me though that I've never understood about clothespin triggers, how does a vertical nail get up and over the plunger head. The way I'm looking at it, it seems like it would just get stuck where the nail is and not catch.
Great mod on a widely available blaster. Seems like people have just been overlooking these because the lack of triggers when we all shoulda been rocken em. Imma go take a look at the bigger xploders models. Springer primaries in every major retailer? I'm excited.
Thanks!
The nail is ground at an angle at the end so the catch will slide down and then back up, so the plunger won't move until you pull the trigger. Not sure if this makes sense, but It is hard for me to put into words.
#314626 Add a trigger to the Xploders Xblaster 200
Posted by
on 20 April 2012 - 10:52 PM
in
Modifications
They fit together fairly well, but you need to goop them together. The 45's are pretty loose in the tee, but the goop eliminates that problem. The only tough part is getting them gooped straight. Not too sure on the deadspace, though.
#314568 Add a trigger to the Xploders Xblaster 200
Posted by
on 20 April 2012 - 06:43 AM
in
Modifications
LEGIT NECRO-BUMP.
Ranges added.
With a 12 stefan hopper with a homemade wye (http://www.nerfrevol....php?f=9&t=3317) and a 12" cpvc barrel, it averages around 83'
Singled with a 14" cpvc barrel, it averages around 90'
All tests done with Revisionfive's Pool noodle darts (http://www.nerfrevol...php?f=26&t=3633)
Here is a picture of the wye I used:
Ranges added.
With a 12 stefan hopper with a homemade wye (http://www.nerfrevol....php?f=9&t=3317) and a 12" cpvc barrel, it averages around 83'
Singled with a 14" cpvc barrel, it averages around 90'
All tests done with Revisionfive's Pool noodle darts (http://www.nerfrevol...php?f=26&t=3633)
Here is a picture of the wye I used:
#314203 Rockets for Nerfers
Posted by
on 09 April 2012 - 05:43 PM
in
General Nerf
D: Somebody backed out. Just $25 more and we will reach the goal again!
#314198 Rockets for Nerfers
Posted by
on 09 April 2012 - 04:20 PM
in
General Nerf
Ignore
#313866 Rockets for Nerfers
Posted by
on 01 April 2012 - 10:07 PM
in
General Nerf
Pledge $15 or more you get one plus 3 rockets.
#313754 Rockets for Nerfers
Posted by
on 30 March 2012 - 05:13 PM
in
General Nerf
Ok, I put a link to this topic on Nerfrevolution, Home of Foam, Hvz forums, and sent it to Jerm on Nerf mods and reviews. Taerkitty has it on Facebook, already.
Edit: Got it on Nerf Mods and reviews: http://www.nerfmodsr...rt-rockets.html
Edit: Got it on Nerf Mods and reviews: http://www.nerfmodsr...rt-rockets.html
#313484 Rockets for Nerfers
Posted by
on 24 March 2012 - 02:25 PM
in
General Nerf
Home of foam: http://homeofnerf.sm...e.com/index.php
#313468 Rockets for Nerfers
Posted by
on 24 March 2012 - 10:49 AM
in
General Nerf
Would you mind if I spread the news about this to other NIC forums?
#312673 How I deal with spiders
Posted by
on 10 March 2012 - 01:28 PM
in
General Nerf
When I kill insects/arachnids, I use high powered blasters with suction darts so it splatters it and doesn't ricochet.
#312486 Homemades Picture Thread
Posted by
on 05 March 2012 - 04:52 PM
in
Homemades
I was gonna make Darthmaker/Kane's "Wyeless Wye", But my local store ran out of PVC 45's. So I Improvised:
It is very sturdy for being just gooped together.
It is very sturdy for being just gooped together.
#312429 Help Identifying Nerf Type Blaster
Posted by
on 04 March 2012 - 05:38 PM
in
General Nerf
I'm pretty sure it is related to this one. They are pretty neat:
Supposedly Makeitgo has something similar.
Supposedly Makeitgo has something similar.
#312289 Nite Finder Rifle 2.0
Posted by
on 02 March 2012 - 11:17 PM
in
Modifications
Very nicely done. I need to make one of these so badly!
#312080 Clear Blaster Tinting
Posted by
on 28 February 2012 - 11:07 PM
in
Modifications
Try it out. If it doesn't stick you can just wash it off and you're not really at a loss. I bet it will work though.
For those who would like to get a really strong tint without waiting forever, mix up your dye and hot water, then add a generous splash of acetone. You really have to be careful not to leave it in for too long, and to be on the safe side you should make sure to use the lower concentration cosmetic stuff, but the acetone makes the plastic just drink up the dye. It'll still be largely transparent if you don't leave it in for too long.
How long would be too long? I really want a trans colored nf now!!!!
#312015 Clear Blaster Tinting
Posted by
on 28 February 2012 - 08:13 AM
in
Modifications
Would this work on polycarb? I would love a tinted pink +bow.
It might, but if it were sanded/frosted, it has a better chance.
#312006 Marchtacular Recapular!
Posted by
on 27 February 2012 - 11:14 PM
in
Nerf Wars
Hmmm I would go for a different location. That's like 45 min. from me.
I live 3 hours away so don't complain. I wish I could go.
#311982 Modification and Paintjob Pictures
Posted by
on 27 February 2012 - 07:40 PM
in
Modifications
I got a shitty LBB from a friend for free and minimized, couplered, and added a new pump handle to it. (The pump handle was gone)
#311948 Clear Blaster Tinting
Posted by
on 27 February 2012 - 01:57 PM
in
Modifications
Oh yeah, I remember your trans purple recon. If the blaster is left in too long, is it going to cause it to deform at all?
#311550 Add a trigger to the Xploders Xblaster 200
Posted by
on 20 February 2012 - 08:43 PM
in
Modifications
As you all know, the Xploders line has a major downside: NO TRIGGERS!!!
I devoted my time today to make a trigger for the Xblaster 200.
Materials:
1. Hot glue/ hot glue gun
2. Dremel w/ cutting disk
3. Zip ties
4. Xblaster 200
5. Sharpie
6. Drill/ Drill bits
7. Nail
8. Plastic Clothespin
9. Masking/electrical tape
10. Pliers
11. Angle bracket
Stock parts:
1. 1/2" PVC Endcap
2. 1/2" PVC 90 or 1/2" PVC TEE
3. Two small blaster screws (Mine are Tek-4 screws)
4. 1/2" PVC 45
5. Some 1/2" PVC
6. Drill/ Drill bit
Instructions:
First, get your Xblaster 200: (Excuse my rscb setup at the moment)
Here are the internals you NEED (Take note of the plunger rod):
Take this pin out of the plunger head:
Take the plunger apart (take note of the order of things):
Take the orange disc that was behind the white tube in front of the white tube. It should look like this:
Wrap take around the back of the white tube. Not too much, just enough to keep the spring behind it:
Fit the Plunger tube and Plunger rod back into the shell and fully draw the plunger rod. Then make a mark where it comes out of the shell:
Line up the mark you made with the back of the shell and make a mark where the orange disc we moved sits on the plunger tube:
Make a line along the bottom of the plunger tube and make a mark all the way around the plunger tube using your previous mark:
Drill in the center of the +:
Take your shell and cut an area like this out of it:
It should look like this:
Make a clothespin trigger like so: http://nerfhaven.com...showtopic=20296
(Adjust the nail as needed) I didn't use epoxy putty to fill it, it isn't holding back a [k26]. I filled it with hot glue after I put the nail in.
Glue it to the Plunger tube:
Put the plunger into the plunger tube:
Assemble the blaster with your choice of barrel system and enjoy your trigger! I am using a 3 streamline/6 stefan RSCB.
INSTRUCTIONS FOR ADDING A STOCK.
First, gather the materials:
Take the endcap, mark, and drill the holes like this (drill bit size depends on the screw size)
Drill corresponding holes in the back of the Xblaster:
Screw the endcap onto the back of the blaster:
Lay out the rest of the materials like so. (you can use a 1/2" 90 instead of the 1/2" tee)
Fit them all together. Glue is optional.
Attach it to the endcap:
Now it is all done.
MONEY SHOT:
I hope this helps all of you with these blasters and were pissed they didn't have a trigger.
With a 12 stefan hopper with a homemade wye (http://www.nerfrevol....php?f=9&t=3317) and a 12" cpvc barrel, it averages around 83'
Singled with a 14" cpvc barrel, it averages around 90'
All tests done with Revisionfive's Pool noodle darts (http://www.nerfrevol...php?f=26&t=3633)
Here is a picture of the wye I used:
I devoted my time today to make a trigger for the Xblaster 200.
Materials:
1. Hot glue/ hot glue gun
2. Dremel w/ cutting disk
3. Zip ties
4. Xblaster 200
5. Sharpie
6. Drill/ Drill bits
7. Nail
8. Plastic Clothespin
9. Masking/electrical tape
10. Pliers
11. Angle bracket
Stock parts:
1. 1/2" PVC Endcap
2. 1/2" PVC 90 or 1/2" PVC TEE
3. Two small blaster screws (Mine are Tek-4 screws)
4. 1/2" PVC 45
5. Some 1/2" PVC
6. Drill/ Drill bit
Instructions:
First, get your Xblaster 200: (Excuse my rscb setup at the moment)
Here are the internals you NEED (Take note of the plunger rod):
Take this pin out of the plunger head:
Take the plunger apart (take note of the order of things):
Take the orange disc that was behind the white tube in front of the white tube. It should look like this:
Wrap take around the back of the white tube. Not too much, just enough to keep the spring behind it:
Fit the Plunger tube and Plunger rod back into the shell and fully draw the plunger rod. Then make a mark where it comes out of the shell:
Line up the mark you made with the back of the shell and make a mark where the orange disc we moved sits on the plunger tube:
Make a line along the bottom of the plunger tube and make a mark all the way around the plunger tube using your previous mark:
Drill in the center of the +:
Take your shell and cut an area like this out of it:
It should look like this:
Make a clothespin trigger like so: http://nerfhaven.com...showtopic=20296
(Adjust the nail as needed) I didn't use epoxy putty to fill it, it isn't holding back a [k26]. I filled it with hot glue after I put the nail in.
Glue it to the Plunger tube:
Put the plunger into the plunger tube:
Assemble the blaster with your choice of barrel system and enjoy your trigger! I am using a 3 streamline/6 stefan RSCB.
INSTRUCTIONS FOR ADDING A STOCK.
First, gather the materials:
Take the endcap, mark, and drill the holes like this (drill bit size depends on the screw size)
Drill corresponding holes in the back of the Xblaster:
Screw the endcap onto the back of the blaster:
Lay out the rest of the materials like so. (you can use a 1/2" 90 instead of the 1/2" tee)
Fit them all together. Glue is optional.
Attach it to the endcap:
Now it is all done.
MONEY SHOT:
I hope this helps all of you with these blasters and were pissed they didn't have a trigger.
With a 12 stefan hopper with a homemade wye (http://www.nerfrevol....php?f=9&t=3317) and a 12" cpvc barrel, it averages around 83'
Singled with a 14" cpvc barrel, it averages around 90'
All tests done with Revisionfive's Pool noodle darts (http://www.nerfrevol...php?f=26&t=3633)
Here is a picture of the wye I used:
#310642 Modification and Paintjob Pictures
Posted by
on 03 February 2012 - 09:00 PM
in
Modifications
What my nitefinder...
...looks like under a blacklight:
...looks like under a blacklight:
#310465 The Fiendfinder (Full write-up with lots of nice pictures)
Posted by
on 31 January 2012 - 11:54 PM
in
Modifications
Since this has been revived, I might as well add that most of the pictures aren't working for me.
#310248 Good Singled Maverick
Posted by
on 28 January 2012 - 12:40 AM
in
Modifications
A for effort! I really just want to take a shit on it, though.
#310230 Homemades Picture Thread
Posted by
on 27 January 2012 - 07:01 PM
in
Homemades
My first homemade, EVER!!!: A SNAPbow Mk. V
I love this thing!
I love this thing!
#309811 Modification and Paintjob Pictures
Posted by
on 19 January 2012 - 09:17 PM
in
Modifications
Xploders pistol thing I got on clearence for $6. It has a 3 streamline/6 stefan RSCB.
#309486 Modification and Paintjob Pictures
Posted by
on 14 January 2012 - 12:41 PM
in
Modifications
LOOK, ANOTHER NITEFINDER!!!! (I promise its not the same one I posted a few days ago)
Ar removed and improved seal Quick 16. Wasn't as tough to get together as some people made it sound. Then again, I might of just been lucky.
Ar removed and improved seal Quick 16. Wasn't as tough to get together as some people made it sound. Then again, I might of just been lucky.
#309228 Modification and Paintjob Pictures
Posted by
on 07 January 2012 - 11:59 PM
in
Modifications
Another halve couplered and minimized Nitefinder:
#309065 Air Horn - Simplest mod ever!
Posted by
on 03 January 2012 - 12:37 PM
in
Modifications
That'd be cool if someone took this idea and made a device that filled air tanks/bladders much faster than pumping.
People have have hooked a bladder up to a tank so their blaster can be semi auto for a while until the bladder runs out. Then they pump the bladder back up and fire all over again.
