I have made my AT2K to be able to exchange the rotating barrels as clips. The links below are to pictures I have of the gun with the clip on and the clip off. I will post instructions later for those of you who can't figure it out by the pictures.
Here's the pictures!
5 replies to this topic
#1
six-hungry-ducks
-
- Members
- 105 posts
Member
Posted 07 June 2003 - 09:22 PM
"It's never the obvious..." -Me
"Trust no one, not even yourself" -Me
"Hey I was watching that!" "It'll be on next Christmas" "Who the hell knows when that's gonna be?" -Peter Griffin
"Trust no one, not even yourself" -Me
"Hey I was watching that!" "It'll be on next Christmas" "Who the hell knows when that's gonna be?" -Peter Griffin
#2
cxwq
-
- Founders
- 3,634 posts
Member
Posted 07 June 2003 - 10:59 PM
Not bad.
What holds the barrel assembly in?
What holds the barrel assembly in?
<meta name="cxwq" content="mostly water">
#3
six-hungry-ducks
-
- Members
- 105 posts
Member
Posted 08 June 2003 - 09:20 AM
The valve and the bottom part of the casing holds the barrels in. When you take apart an AT2K, you'll notice the groove at the front of the gun that holds the barrels in place. All you have to do is cut it in half until you get about a 1/4 of an inch behind it. Don't screw in the 2 screws at the front, and if you have to, don't screw in the one closes to the front of the gun that is near the liquitron power gauge. There you have it. That's all you have to do to be able to change turrets like clips.
"It's never the obvious..." -Me
"Trust no one, not even yourself" -Me
"Hey I was watching that!" "It'll be on next Christmas" "Who the hell knows when that's gonna be?" -Peter Griffin
"Trust no one, not even yourself" -Me
"Hey I was watching that!" "It'll be on next Christmas" "Who the hell knows when that's gonna be?" -Peter Griffin
#4
rawray7
-
- Members
- 549 posts
Member
Posted 08 June 2003 - 01:16 PM
yeah, that's a pretty good mod if you have lots of broken AT2ks. i had about 3 broken 1500s, so i did that to my fourth one. the only thing i would recommend differently is keeping the top part of the plastic that you cut off, and attaching it back on the gun, but on a hinge. so, you flip it up to load a new assembly, flip it down and it's all stable.
You, nerfboi, are the suckest gun. -neonerfer
#5
silent mercenary
-
- Members
- 158 posts
Member
Posted 08 June 2003 - 02:19 PM
nice
does its distance suffer any?
does its distance suffer any?
I will not walk, so that a child may live!
- Master Shake
- Master Shake
#6
six-hungry-ducks
-
- Members
- 105 posts
Member
Posted 09 June 2003 - 09:32 AM
No, the distance is the same as it would be without this mod.
Yes I did keep the top part of the plastic and I'm going to do exactly what you said rawray.
Yes I did keep the top part of the plastic and I'm going to do exactly what you said rawray.
"It's never the obvious..." -Me
"Trust no one, not even yourself" -Me
"Hey I was watching that!" "It'll be on next Christmas" "Who the hell knows when that's gonna be?" -Peter Griffin
"Trust no one, not even yourself" -Me
"Hey I was watching that!" "It'll be on next Christmas" "Who the hell knows when that's gonna be?" -Peter Griffin
1 user(s) are reading this topic
0 members, 1 guests, 0 anonymous users
